UIP-1602 / UIP-3202 IP Cat5 KVM Installation screw A: M3.2 x 4.5 mm A B iew rV be Cy screw B: M4 x 10 mm ■ Install each bracket using screws provided shown in Figure 1. ■ Fix the KVM into the rack Figure 1. Installing the bracket to the KVM. iew rV be Cy Figure 2. Fixing the KVM into the rack.
UIP-1602 / UIP-3202 IP Cat5 KVM Package Content (only for rackmount KVM) 1 5 al User Manu 2 3 4 6 7 1 KVM switch x 1 pc 2 Screw M3.2 x 4.
UIP-1602 / UIP-3202 IP Cat5 KVM Connection UIP-1602 Dual power Local with failover Console USB Serial Ethernet Cascade UIP-3202 Connection Rackmount KVM Internet hub Cat5 cable (up to 132 ft) Cat5 cable DG-100S dongle Connection KVM modules Internet hub back Cat5 cable Cat5 cable (up to 132 ft) DG-100S dongle ■ For USB & serial connection, please refer to the attached IP KVM user manual
UIP-1602 / UIP-3202 IP Cat5 KVM Cascade ■ Cascaded KVM ( Bank 2 to 8 ) must be single console Cat5 KVM - U-1601 / U-3201 ■ With the UIP-1602 cascade up to 128 servers. With the UIP-3202 cascade up to 256 servers.
DG-100 / DG-100S Dongle Connection DG-100 PS/2 dongle ■ To connect DB-15 connector to the computer’s video card ■ To connect keyboard connector to the computer’s keyboard port ■ To connect mouse connector to the computer’s mouse port mouse Cat5 KVM switch Keyboard DB-15 Cat5 cable (up to 132 ft) DG-100 PS/2 dongle PS/2 server DG-100S USB dongle ■ To connect DB-15 connector to the computer’s video card ■ To connect USB connector to the computer’s USB port Cat5 KVM switch USB DB-15 Cat5 cable (up to 13
KVM Membranes Power ON ■ Turn off all servers and KVM switches ■ Make sure all cables / connectors are properly connected ■ Recommend Power ON sequence is monitor, KVM switch finally computer Front Panel - Port LED Indications 16 ports Bank no. PC port LEDs Channel button Bank button 32 ports Bank no.
Password The password is disabled by default ( i.e. There is no password required when you power on the KVM switch for the first time) ■ Enable password 1. Press the KVM hotkey Scroll Lock + Scroll Lock + U 2. Logout the KVM by pressing the hotkey Scroll Lock + Scroll Lock + P 3. In SUPERVISOR level, enter “00000000” eight zeros in user name & password field (Do not use “0” on number pad) 4.
KVM OSD OSD Menu OSD operation next to the system name The PC is powered on next to the system name The PC is selected F1 Access F1 MAIN MENU F2 Logout the OSD menu F3 Previous menu Esc Cancel / Quit Enter Complete / Switch to selected port Switch to previous or next port PgUp/PgDn Switch to previous bank or next bank 1/2/3/4 Display port 01 ~ 08 / 09 ~ 16 / 17 ~ 24 / 25 ~ 32 Remark: Display port 17 ~ 32 for 32 port model only F1 Main Menu 01 LANGUAGE OSD language change 02 PORT NAME E
KVM Hotkey Local Console Hotkey Hotkey Function Scroll Lock + Scroll Lock + Space Bar Calling OSD menu Right-button mouse + Esc Calling OSD menu Scroll Lock + Scroll Lock + Switch to previous port Scroll Lock + Scroll Lock + Switch to next port Scroll Lock + Scroll Lock + PgUp / PgDn Switch to previous bank or next bank Scroll Lock + Scroll Lock + Bank no. + Port no.
UIP-1602 / UIP-3202 IP Remote Setup Quick Installation Guide of IP KVM for remote access Please perform the follow steps 1. Power off all KVM hardware and connected devices. 2. Connect the power supply to IP KVM 3. Connect the monitor, keyboard & mouse to console port of IP KVM (not applicable to integrated LCD drawer version ) 4. Connect the KVM cable to IP KVM and target servers 5.
UIP-1602 / UIP-3202 IP Remote Setup 4. Remote access the IP-KVM switch via Web Using the HTTP protocol or a secure encrypted connection via HTTPS and entering the configured IP address of IP KVM switch into the web browser to remote access the IP KVM switch. With successful connection to IP KVM, the login page will show as below, then key in the default user name & password 5.
Optional Accessories 1. Cat5 cable 1.1 CU-3 3 feet 1.2 CU-6 6 feet 1.3 CU-10 10 feet 1.4 CU-15 15 feet 1.5 CU-33 33 feet 1.6 CU-66 66 feet 2. Cat5 / USB KVM cascade cable 2.1 CBC-6 6 feet 3. PS/2 Dongle for Cat5 KVM 3.1 DG-100 PS/2 4. USB Dongle for Cat5 KVM 4.1 DG-100S USB 5. Power cord 5.1 IEC power cord 5.2 NEMA 5-15 power cord (US) 5.3 BS 1363 power cord (UK) 5.4 CEE 7/4 power cord (German) 5.
DC Power 12V, 24V, 48V Input Model 12V 24V 48V Input voltage: 12-Volt 24-Volt 48-Volt Input range: 9 ~ 18V 18 ~ 36V 36 ~ 75V - No load 50 mA 50 mA 50 mA - Full load 4950 mA 2450 mA 1220 mA Output voltage: 12-Volt 12-Volt 12-Volt Output current: 4.16A 4.16A 4.
Specification UIP-1602 / UIP-3202 ▀ ▀ ▀ KVM Port Number of ports: 16 or 32 Connector: RJ-45 Connectivity: DG-100S USB dongle / DG-100 PS/2 dongle up to 132 feet Local Console Graphic connector: HDDB15-pin Resolution: Up to 1600 x 1200 Input device: 2 x USB type A for keyboard & mouse IP Remote Console Connector: RJ45 Ethernet User management: 15-user login, 1 x active user Network protocol: DHCP / BOOTP / DNS Security: SSL v3, RSA, AES, HTTP / HTTPs, CSR Resolution: Up to 1600 x 120
FAQ General 1. How do the KVM switches allow the user to switch ports? There are two ways to switch ports. One is the membrane buttons on the front and the other way is with Hot-key commands. 2. What operating systems do the KVMs support? The KVMs support multi-platform support allows you to control Windows-based computers, Sun Solaris systems, Linux, or even Macs by a single KVM switch.
FAQ 10. The server VGA resolution does not match the resolution of monitor ? The KVM supports DDC function which will dynamically detect and the DDC data. The problem may come from the power on sequence. For KVM switch The recommended power on sequence is - monitor, KVM switch and then servers. For remote console box It supports DDC function but does not support hot-plug, the recommend power on se quence is – monitor, remote console box and then servers.
Troubleshooting 1. There is no LED display on KVM membrane switch i. Make sure the power adapter plugged into the KVM Switch, if the LED’s still off, perform soft reset to KVM switch. ii. Power cycle KVM switch. 2. I can power on the KVM, but I am not getting any picture at all, how can I solve this? Switching to another port and checking if this port has the same problem a. If you switch to another port, please check the screen resolution is the same. b.
