OLED Display Manual OLED DISPLAY INSTRUCTION MANUAL (RLVBDSP04, RLVBDSP05–F, RLVBDSP05–L, RLVBDSP05-M and RLVBDSP05–H) RLVBDSP04 RLVBDSP05 -1- 12/06/09
OLED Display Manual Contents OLED Setup ............................................................................................................................ 4 Video VBOX Pro / LITE / Waterproof .................................................................................. 4 VBOX Micro/ Performance Box Sport ................................................................................. 4 VBOX3i/ VBOX3/ VBSX/SL ...................................................................................
OLED Display Manual Set Start & Splits ............................................................................................................... 11 Reset Laptiming Data........................................................................................................ 12 Clear Start & Splits ............................................................................................................ 12 Brightness......................................................................................
OLED Display Manual OLED Setup Video VBOX Pro / LITE / Waterproof When setting up the DSP04 OLED display with a Video VBOX, it is important to connect to the correct port of the OLED display. The OLED display only has a serial connection on the lower connector, with the buttons on the right hand side - as shown in this picture. The configuration is indicated on a label on the rear of the OLED display. To connect to a Video VBOX Lite, you should connect the cable into the ‘AUX’ port.
OLED Display Manual Display Modes The OLED display has different display modes that are accessed using the up and down buttons. The data displayed on each screen is calculated at all times, even if it is not currently displayed. Speed In this mode the screen will display a large clear speed value to 2 decimal places, including the units, mph or km/h. The number of decimal places displayed can be adjusted through the OLED menu.
OLED Display Manual Fastest Lap The difference between the new lap time and the best lap time will be shown with a + or – sign. A ‘–’ is shown when a faster than best is achieved and a ‘+’ is shown for a slower than best. Split line display If split lines have been set inside the OLED display then it will display the split time for between 2 and 20 seconds (as configured) when the split line is crossed.
OLED Display Manual Predictive Lap Timing To use this, the OLED must have start/finish information set, or an Auto Track-Map element in the VVB scene. Until the start line is crossed, the screen will show ‘Waiting For Start Line’. On the first lap, the OLED will create a reference lap. The reference lap will be replaced with any subsequent quicker lap time. If you wish to fix this comparison lap time at any point, then this can be done by pressing the button.
OLED Display Manual Setup Menu Options - MENU The OLED display menu is accessed by pressing the button when the ‘Menu’ screen is shown. The menu can be navigated with the▲and▼ buttons. Multiple Scene Selection The Video VBOX can store up to 8 user defined scenes. They are loaded by placing them in the root folder of an SD card and inserting them into a VVB. The user can select the scene using an OLED display.
OLED Display Manual About In this section you can find serial numbers and firmware versions installed in the OLED and connected VVB unit. Predictive Lap Timing Settings Bar Range This setting alters the amount of +/- time shown on the bar graph during lap prediction. Either 2, 5, 10 or 30 seconds can be chosen. Press to when bar range is highlighted to scroll through different time options. Transfer Ref.
OLED Display Manual Speed Units If the button is pressed the OLED display allows the user the ability to select the units of the displayed speed. Highlight the desired measurement type and press to select. Press Press Select Exit and Press Speed Decimal Places Pressing the button will cycle through 0, 1, and 2 decimal places. Rolling Lap Time This function shows a continuously counting lap time which briefly freezes as the start/finish line is crossed.
OLED Display Manual One Shot Mode This mode is used for timing from a standing start to a finish line – e.g. sprint racing, hill climbs. When one shot mode is enabled, when the user comes to a stop, after 2s, the screen counts down from 5 then shows ARMED – Start when ready. Press to tick option, then Exit Menu Press Stop Vehicle After Countdown If the user pulls away before 1 is shown on the screen, nothing changes.
OLED Display Manual Reset Laptiming Data When this option is highlighted, pressing the button causes the stored reference lap, lap count and lap times to be reset. Using this option fully resets Predictive Lap Timing mode. Clear Start & Splits When this option is highlighted, pressing the button clears the start/finish and split lines. Brightness To adjust the level of brightness on the display screen, press the button to move through the 5 different light levels.
OLED Display Manual Upgrading the OLED Display firmware It is recommended to check the web site periodically for updates. The OLED upgrade files have a .RUF file extension. The latest firmware for Video VBOX and OLED can be found here. Upgrade OLED through Video VBOX Please note that you must be running at least VideoVBOX firmware version 003.000 Build 0025 to upgrade the OLED like this. New VVB firmware comes with OLED firmware built in.
OLED Display Manual Troubleshooting See below for possible error messages and causes. No serial data being received from VVB. Check scene settings under serial application is set to OLED. Check connector is in corrected into ‘SER’ port on PRO/ ‘DATA’ port on 2CAM/ ‘AUX’ port on LITE. Check using lower connector on OLED (DSP04). Over 50KM away from loaded SF line. Check correct SF line loaded into VVB. Stop VVB logging data before attempting to load a reference lap.
OLED Display Manual Connector Assignments & Specifications VBOX OLED Display with Waterproof Aluminium Housing (VBDSP04) Compatibility VBOX 3i, Video VBOX, VBOX 20SX, VBOX 20SL, VBOX 20SL3, VBOX III, VBOX Micro, Performance Box Sport. Choose lead below for correct connection.
OLED Display Manual VBOX OLED Display with Splash proof Plastic Housing - LEMO connector (VBDSP05) Compatibility Unit Connection Output Connection IP Rating Operating Temp Storage Temp Power Input Voltage Dimensions Weight VBOX 3i, Video VBOX, VBOX 20SX, VBOX 20SL, VBOX 20SL3, VBOX III Fixed flying cable (2m) LEMO 5W Plug (DSP05 – L), Mini DIN 5W Plug (DSP05 – M), Fischer 5W Plug (DSP05 – F) IP64 -40C to +70C -40C to +85C 1.2 W 6 – 30VDC 101 x 51.5 x 26.5mm (exc. cable) 146g (exc.
OLED Display Manual Contact Details Address: Racelogic, Unit 10, Swan Business Centre, Osier Way, Buckingham, Bucks. MK18 1TB United Kingdom Email: support@racelogic.co.uk Web: www.racelogic.co.uk Document Updates Rev Date Changes Page Init Change Draft 30-Apr-09 -- Draft Version of Document. AM 1 21-May-09 -- Additional Screenshots and Firmware upgrade description added.
