User`s manual
User’s Manual 9
2.2.2 Connect Programming Cable
The programming cable connects the RCM3400 to the PC running Dynamic C to download
programs and to monitor the RCM3400 module during debugging.
Connect the 10-pin connector of the programming cable labeled
PROG to header J2 on the
RCM3400 Prototyping Board as shown in Figure 3. Be sure to orient the marked (usually red)
edge of the cable towards pin 1 of the connector. (Do not use the
DIAG connector, which is
used for a normal serial connection.)
Figure 3. Connect Programming Cable and Power Supply
NOTE: Be sure to use the programming cable (part number 101-0542) supplied with this
Development Kit—the programming cable has blue shrink wrap around the RS-232
converter section located in the middle of the cable. Programming cables with clear or
red shrink wrap from other Rabbit Semiconductor kits are not designed to work with
RCM3400 modules.
Connect the other end of the programming cable to a COM port on your PC.
NOTE: Some PCs now come equipped only with a USB port. It may be possible to use
an RS-232/USB converter (Part No. 540-0070) with the programming cable supplied
with the RCM3400 Development Kit. Note that not all RS-232/USB converters work
with Dynamic C.
DCIN
R58
+5 V
+3.3 V
+3.3 V
GND
+5 V
GND
GND
+5 V
GND
GND
+3.3 V
+3.3 V
+5 V
+5 V
+5 V
GND
GND
+3.3 V
+3.3 V
S1
2
1
2
1
DS2
R57
PD7
PD4
R4
R5
R3
C2
R1
R2
R9
C6
C9
C3
C1
IR1
60
59
RS-485
JUMPER
DEFAULT (12, 56)
R26
R22
C13
U2
R21
JP3
JP8
JP4
PG6
PG7
C26
C23
CX3
CX4
CX5
CX7
CX8
CX6
CX9
CX10
CX11
RESET
1
2
R39
R40
R41
R42
R62
C31
C32
R45
C33
C34
C35
C36
C37
U7
C40
U6
R59
C47
C45
C50
C51
C49
C52
C48
C44
C42
C41
R48
C38
C49
C39
R50
R51
R53
R54
R52
R56
R55
C46
C43
Y1
J7
RS-232
J6
TxF
RxF
RxE
TxE
GND
C30
RxD
TxD
GND
R46
TxC
RxC
RS-232
J5
U5
C29
C28
C27
C24
C21
C19
U4
J4
+485 GND 485
C18
C22 C25
BT1
DS4
DS3
LINK ACT
R60
R61
CURRENT
MEASUREMENT
OPTION
JP10
DS5
POWER
R65
L1
D1
J8
D2
J9
C61
U12
C58
C57
C54
C55
U10
C56
HOT
C59
C60
U13
+BKLT
/CS
LED1
LED3
LED5
A2
A0
D1
D3
D5
D7
GND GND
LCD1JA
LCD1JB
LCD1JC
A2
A1
D1
D3
D5
D7
GND
A3
A1
D0
D2
D4
D6
GND
+V
/RESET
LDE0
LED2
LED4
LED6
GND
+BKLT
/CS
LED1
LED3
LED5
GND
GND
R64
+5 V
Battery
PA0
PA2
PA4
PA6
PB1
PB3
PB5
PB7
PC1
PC3
PC7
/IOWR
SMODE1
PD0
PD5
PD7
PE1
PE4
PE6
PF0
PF4
PF6
PG0
PG2
PG4
PG6
/RES OUT
+3.3 V
VBAT
GND
RN2
RN1
PA1
PA3
PA5
PA7
PB2
PB4
PB6
PC0
PC2
PC6
/IORD
STAT
SMD0
PD4
PD6
PE0
PE2
PE5
PE7
PF1
PF5
PF7
PG1
PG3
PG5
PG7
RESET IN
GND
+3.3 V
GND
J1
J2
PROGRAM
R6
R7
R10
C7
R16
C5
CX2
UX2
CX1
UX1
U3
RCM1JB
RCM1JA
2
34
R25
R28
R19
33
1
R67
JP6
JP7
420 mA
JP9
JP5
JP2
JP1
U1
C11
R13
R14
R29
R31
R34
R36
C8
C4
R8
R11
R12
R15
R18
R23
R27
R32
R35
R38
C10
C12
R17
C14
R20
C15
R24
C16
R30
C17
R33
C20
R37
J3
RCM3400
PROTOTYPING
BOARD
GND AIN0 AIN1 AIN2 AIN3 AIN4 AIN5 AIN6 THERM GND CNVRT VREF
S2
S3
DS1
R43
R44
PD5
PD6
R47
+V
/RES
ET
LED0
LED2
LED4
LED6
GND
A3
A1
D0
D2
D4
D6
C53
3-pin
power connector
JP1
C61
C59
C56
JP2
R21
C40
C39
C33
C34
C28
U3
C22
U2
C48
C53
C51
RP2
RP3
RP4
JP3
C55
C50
R25
R24
C62
D1
C35
R20
R18
R17
R13
C32
R11
C31
Y1
U5
U7
U1
C9
C8
R1
R4
C1
C3
C4
C5
C24
C25
C19
C14
C13
C2
R3
Colored
edge
To
PC COM port
PROG
J2
Blue
shrink wrap
PROG
DIAG
Programming
Cable