User`s manual

12 eDisplay (OP7200)
2.3 Programming Cable Connections
Connect the programming cable to download programs from your PC and to program and
debug the OP7200.
NOTE: Use only the programming cable that has a red shrink wrap around the RS-232
level converter (Part No. 101-0513), which is supplied with the OP7200 Tool Kit. Other
Rabbit programming cables might not be voltage-compatible or their connector sizes
may be different.
Connect the 10-pin PROG connector of the programming cable to header J1 on the
OP7200’s RabbitCore module. Ensure that the colored edge lines up with pin 1 as shown.
(Do not use the DIAG connector, which is used for monitoring only.) Connect the other end
of the programming cable to a COM port on your PC. Make a note of the port to which
you connect the cable, as Dynamic C will need to have this parameter configured. Note
that COM1 on the PC is the default COM port used by Dynamic C.
Figure 3. Programming Cable Connections
NOTE: Some PCs now come equipped only with a USB port. It may be possible to use an
RS-232/USB converter (Part No. 20-151-0178) with the programming cable supplied
with the OP7200 Tool Kit. Note that not all RS-232/USB converters work with
Dynamic C.
D23
D20
+
P
W
R

P
W
R
+
K
O
U
T
0
O
U
T
1
O
U
T
2
O
U
T
3
O
U
T
4
O
U
T
5
O
U
T
6
O
U
T
7
G
N
D
IN
1
2
I
N
1
3
IN
1
4
IN
1
5
/
R
S
T
T
X
C
R
X
C
T
X
D
R
X
D

4
8
5
+
4
8
5
G
N
D
J10
Q31
J
P
9
J15
R44
R41
R
4
2
R
4
0
R31
R29
R
4
3
R46
R
4
5
C
3
3
J
P
4
R
1
9
R
2
6
R
2
7
R
3
0
R28
R25
R20
C
2
R
1
7
R
1
6
IN
1
6
I
N
1
7
I
N
1
8
A
IN
0
A
I
N
1
A
I
N
2
A
I
N
3
A
IN
4
A
IN
5
A
I
N
6
A
I
N
7
A
G
N
D
R
1
8
C
4
R
1
5
R
1
R
2
C
1
J
P
1
D13
D12
D14 D15
C
5
Y1
C
6
0
C
6
1
Q5
U2
1
60
C
5
7
D11
R
7
9
R
7
8
R
7
7
R
7
6
R
7
5
R
7
4
C
3
6
J
P
2
J
P
7
I
N
0
IN
1
IN
2
IN
3
IN
4
IN
5
I
N
6
I
N
7
IN
8
I
N
9
IN
1
0
I
N
1
1
C43
C44
R
8
2
R
8
3
R
8
4
J9
R
8
5
R86
R165
R164
R162
R
8
9
R
8
7
R
8
8
C
5
1
C
5
0
R90
C48
J
P
3
J12
R71
R72
R59
R60
R66
C40
C
6
6
J
P
6
J
P
5
R
1
0
8
C
6
5
J
P
8
R61
R159
R
1
4
7
Q12
J7
Q13
C39
C49
C13
L9
D24
LS1
JP10
1
3
2
4
MSTR
SLAVE
D1
D
3
D
2
D
5
D
4
Q2
R
2
4
Q4
R
2
3
Q3
R
2
2
Q8
R
3
8
Q7
R
3
7
Q6
R
3
9
Q11
R
5
5
Q10
R
5
6
D
6
D
8
D
9
R
6
4
R
6
2
R
6
5
C
8
6
C
2
9
C30
C16
C17
C18
C6
C8
C7
R91
R14
D
S
1
D
S
2
T
V
S
1
C
8
2
J8
R
1
5
2
R
1
5
1
C
8
5
C
8
4
R
1
4
9
J13
J16
J2
J6
J3
R36
R169
R80
R81
D10
C32
C31
L2
Battery
CAUTION
J14
J1
R2
C
3
D2
R7
C
2
7
R8
R36
RT1
R
4
1
R37
R
3
8
D1
R
3
9
Y2
C2
C1
U8
U7
U3
U6
C7
GND
GND
EGND
DS2
L
N
K
ACT
D
S
1
R19
Q3
Q4
Q5
Q2
R1
Y1
C4
C17
C8
R9
R
1
3
R
1
1
U1
BT1
R15
C12
R17
R20
C13
Y3
R16
R22
R21
C14
R18
C
2
5
C28
D3
J2
JP4
JP
3
JP1
JP6
C30
JP2
JP5
C29
U2
Flas
h
EP
RO
M
J2
J6
J3
J10
PROG
1
1
1
1
E-Net
R-Net
1
USR PWR
LNK ACT
CAUTION: Disconnect power
before making or removing
terminal connections.
Programming
Cable
To
PC COM port
Colored edge
PROG
J1
DIAG
PROG
Red
shrink wrap