Specifications
NEW FROM CHIPCON NEW FROM CHIPCON NEW FROM CHIPCON NEW FROM CHIPCON
Wireless Solutions
Chipcon
15
14
13
12
11
1
2
3
4
5
6 7 8 9 10
20 19 18 17 16
C51
GD00
CSn
XTAL
C81 C101
C124
C131
C121
CC1100
CC1110
SCLK
S0 (GD01)
GD02
DVDD
Antenna
(50 Ohm)
1.8V-3.5V power supply
R171
SI
SCLK
S0
(GD01)
GD02
(opt.)
(opt.)
DIE ATTACH PAD:
DCOUPL
AVDD
AVDD
RF_P
RF_N
AVDD
GD00
CHs
X0SC_Q1
AVDD
X0SC_Q2
SI
GND
RBIAS
DGUARD
GND
L121
L131
L122
C122
C125
C123
L123
RADIO CONTROL
PACKET HANDLER
FEC / INTERLEAVER
TXFIFO
90
0
RXFIFO
MODULATOR
PA
ADC
FREQ
SYNTH
BIAS X0SC
DEMODULATOR
DIGITAL INTERFACE TO MCU
ADC
SCLK
S0 (GD01)
SI
CSn
RF_P
RF_N
RBIAS X0SC_Q1 X0SC_Q2
GD02
GD00
LNA
Digital Inter
f
ace
C232
L233 L232
C233
Antenna
(50 Ohm)
Optional:
L241
C241
C234
C231
L231
2.0V – 3.6V Power Supply
C301
R271
1
P1_2
2
DVDD
3
P1_1
4
P1_0
5
P0_0
6
P0_1
7
P0_2
8
P0_3
9
P0_4
27
R_BIAS
26
AVDD
25
AVDD
24
RF_N
23
RF_P
22
AVDD
18
P2_4/XOSC32_Q2
17
P2_4/XOSC32_Q1
16
P2_2
15
P2_1
14
P2_0
13
P0_7
12
P0_6
11
P0_5
10
AVDD
21
XOSC_Q1
AGND
Exposed die
attached pad
I/O CONTROLLER
X2
C171
C181
20
XOSC_Q2
19
AVDD
X1
C201
C211
C235
8051 CPU
CORE
32kB
FLASH
4 KB SRAM
FLASH CTRL
DEBUG
INTERFACE
RESET
CLOCK & MUX
CALIBRATION
RESET_N
32.768 kHz
XTAL OSC
26 MHz
XTAL OSC
High
Speed
RC-OSC
34 kHz
RC-OSC
RAM
WATCHDOG
FLASH
UNIFIE
D
AGC
RF_P RF_N
MODULATOR
SYNTH
DEMOD-
ULATOR
POWER MGT.
CONTROLLER
CODE
SFR bus
XDAT A
DAT A
SF R
XOSC_Q2
XOSC_Q1
XMIT
CHAIN
ADC
Audio/ DC
VDD (2.0 – 3.6V
DCOUPL
ON-CHIP VOLT
REGULATOR
Power On Reset
P0_0
P0_1
P0_2
P0_3
P0_4
P0_5
P0_6
P0_7
P1_0
P1_1
P1_2
P1_3
P1_4
P1_5
P1_6
P1_7
P2_0
P2_1
P2_2
P2_4
P2_3
MEMORY
ARBITRATOR
DMA
IRQ CTRL
USART 0
SRF bus
AES
ENCRYPTION
and
DECRYPTION
TIMER (16-bit)
TIMER 3 (8-bit)
TIMER 2 (8-BIT MAC)
TIMER 4 (8-bit)
USART 1
SLEEP TIMER
RADIO REGISTERS
RADIO DATA INTERFACE
RECEIVE
Frequency
Synthesizer
Frame Control
CHAIN
36
P1_3
35
P1_4
34
P1_5
33
P1_6
32
P1_7
31
RESET_N
30
DCOUPL
29
AVDD_DREG
28
GUARD
Digital
Analog
Mixed
CHIPCON Single-Chip RF Transceivers
9
www.mouser.com/chipcon
(800) 346-6873
The CC1100 multi-channel RF transceiver is the world's lowest total system cost radio intended for use in the 315, 433, 868, and 915 MHz frequency bands. With its very low power consumption and excellent radio performance, the
CC1100 is a perfect solution for applications in for instance home and building automation, wireless alarm and security systems, and consumer electronics, to mention a few. The CC1100 transceiver is based on Chipcon's latest
product platform, the SmartRF®04 Technology, which is built upon an advanced 0.18μm CMOS technology facilitating superior RF performance in combination with high-density and low-power integration of digital modules.
MOUSER
STOCK NO.
Chipcon/TI
Part No.
Frequency
(MHz)
Description
Price
Each
839-1100/50DK-433 CC1100_CC1150DK-433MHz 433 Full Development Kit - two SmartRF®04 evaluation boards, two CC1100EM evaluation modules, 510.00
one CC1150EM evaluation module, antennas and cables
839-1100/50DK-868 CC1100_CC1150DK-868MHz 868/915 Full Development Kit - two SmartRF®04 evaluation boards, two CC1100EM evaluation modules, 523.14
one CC1150EM evaluation module, antennas and cables
CC1100/CC1150 LOW-COST UHF RF TRANSCEIVER/TRANSMITTER CHIPS
Features:
•
Market's lowest system cost.
•
Very few external components required.
•
Very small footprint. The CC1100 comes in a 4x4mm, 20-pin QLP package.
•
Reference design with two-layer PCB and all components mounted on the same side.
•
CC1100's many powerful digital features make it easy to build a high-performance RF
system using an inexpensive microcontroller.
Excellent Radio Performance:
•
High sensitivity: -110dBm @ 1.2kbps
•
Programmable data rate from 1.2-500kbps.
•
Robust solution with excellent selectivity and blocking performance.
•
Programmable output power up to +10dBm for all supported frequency bands.
•
Ideal for multichannel operation: 50-500kHz channels
Very low power consumption:
•
RX: 15.6mA, TX: 28.8mA @ +10dBm output power, Powerdown: 400mA.
•
Burst mode data transmission with high over-the-air data rate reduces current consumption.
•
Automatic RX polling using Wake-on-Radio: 1.8μA.
Applications:
•
Home and building automation
•
Automatic meter reading (AMR)
•
Wireless alarm and security systems
•
Industrial monitoring and control
•
Wireless sensor networks
•
Consumer electronics
•
Ultra low-power wireless applications.
•
Operating in the 315, 433, 868, 915 MHz ISM/SRD bands
CC1100/CC1150 Development Tools
CC1100/CC1150 Chips
For quantities of 100 and up or for Tape & Reel, call for quote.
Application Circuit
Block Diagram
The CC1110 is a powerful 315/433/868/915 MHz System-on-Chip designed for low-power and low-voltage wireless communication applications.
With a multi-channel 315/433/868/915 MHz radio transceiver, a single-cycle 8051 microcontroller and 32 kB Flash memory, this unique
all-in-one device makes it easier than ever to finish your design while offering numerous application possibilities.
MOUSER
STOCK NO.
Chipcon/TI
Part No.
Freq.
(MHz)
Description
Price
Each
839-1110DK-433 CC1110DK-433 433 Full Development Kit - two SmartRF
®
04 evaluation boards, 710.00
two CC1110EM evaluation modules, antennas and cables
839-1110DK-868 CC1110DK-868/915 868/915 Full Development Kit - two SmartRF
®
04 evaluation boards, 693.00
two CC1110EM evaluation modules, antennas and cables
CC1110 UHF RF SOC TRANSCEIVER
WITH ONBOARD 8051 MICROCONTROLLER CHIP
Features:
•
High-performance and low-power RF transceiver core – the industry leading CC1100
•
High performance and low power 8051microcontroller core, typically with 8 times the
performance per MHz of a standard 8051
•
32 kB in-system programmable flash
•
4 kB SRAM (with data retention in all power modes)
•
Four flexible power modes for reduced power consumption
•
System clock source can be 16 MHz on-chip RC oscillator or 26 MHz crystal oscillator.
The 26 MHz oscillator is used when radio is active
•
Real time clock with low-power 32.768 kHz crystal oscillator or internal low-power 34 kHz RC-oscillator
•
Very fast transition times from sleep modes to active enables ultra low average power consumption ºin low duty-cycle systems
•
In deep sleep modes the system can wake up on external interrupts or real time counter events
•
Excellent receiver selectivity and blocking performance and high sensitivity
•
Programmable data rate up to 500 kbps
•
2-FSK, GFSK and MSK supported
•
Low current consumption (Total: RX: 22 mA, TX: 23 mA, w/ microcontroller running at 26 MHz)
•
Ideal for frequency hopping systems and multichannel operation
•
Very few external components: Complete on-chip frequency synthesizer,
no external filters or RF switch needed
•
8-14 bits ADC with up to eight inputs
•
Wide supply voltage range (2.0V – 3.6V)
•
Programmable Watchdog timer
•
Power On Reset
•
On-chip temperature sensor
Applications:
•
AMR
•
Active RF-ID systems
•
Alarm & security systems
CC1110 Development Tools
CC1110 Chips
MOUSER
STOCK NO.
Chipcon/TI
Part No.
Description
Price Each
25
1
For quantities of 100 and up or for Tape & Reel, call for quote.
839-CC1110 CC1110-RTY1 36Pin QLP Transceiver (packaged in tray) 6.49 5.96
Application Circuit
Block Diagram
•
Home automation
•
Telemetry
•
Wireless payment systems
•
16-bit timer + three 8-bit timers
•
True random number generator
•
Hardware debug support
•
21 general I/O pins, two with 20 mA sink/source capacity
•
In-circuit interactive debugging
MOUSER
STOCK NO.
Chipcon/TI
Part No.
Description
Price Each
25
1
839-CC1100 CC1100-RTY1 20 Pin QLP Transceiver (packaged in tray) 3.96 3.33
839-CC1150 CC1150-RTY1 16 Pin QLP Transmitter Only (packaged in tray) 2.39 1.98
© Copyright 2007 Mouser Electronics
© Copyright 2007 Mouser Electronics
NEXT
BACK
NEXT
BACK
© Copyright 2007 Mouser Electronics
© Copyright 2007 Mouser Electronics
NEXT
BACK
NEXT
BACK
Mouser Catalog Download