Specifications

Wireless Solutions
DLP Design
[phone]
14
DLP DESIGN RFID and ZigBee™ Modules
DLP-RF1 - 2.4 GHZ OEM RF USB Transceiver Module With USB Interface
MOUSER
STOCK NO.
DLP
Part No.
Price Each
1 10 100
DLP-RF2
MOUSER
STOCK NO.
Description
For quantities of 500 and up, call for quote.
www.mouser.com/dlpdesign
626-DLP-RF1-Z DLP-RF1-Z DLP-RF1-Z USB Transceiver Module for Computer Control Functions 59.95 53.10 49.95
626-DLP-RF2-SENS DLP-RF2-SENS Temperature and Humidity Sensor Board for RF2 Module 59.95 58.00 56.26
626-DLP-RF2-RELAY DLP-RF2-RELAY Latching Relay Board for RF2 Module 49.95 48.20 46.75
626-DLP-RF2-PROTO DLP-RF2-PROTO Proto Development Board for RF2 Module Applications 99.95 95.50 90.70
For quantities of 500 and up, call for quote.
The DLP-RF1 and DLP-RF2 OEM Modules are short-range, low-power, 2.4-GHz, unlicensed worldwide ISM band transceivers designed around the IEEE 802.15.4 Wireless Standard. Both support point-to-point and star network
configuration using preprogrammed firmware.
The RF1 and RF2 are ready for either direct design into finished product or as a quick wire replacement within a home or office application. The units come preprogrammed with DLP Design’s Serial Interface Packet Processor (SIPP™)
firmware based upon Freescale’s SMAC RF IC control firmware. If the SIPP™ firmware does not meet the requirements of the project at hand, then the BDM interface is available for reprogramming the microcontroller with user firmware.
Application Areas:
•
Remote control and wire replacement in industrial systems
•
Wireless sensor networks
•
Home automation and control
•
Factory automation
•
Heating and cooling systems
•
Inventory management and RFID tagging
•
Human interface devices
•
Remote entertainment control
•
Wireless toys
Features:
•
IEEE 802.15.4 Compliant & ZigBee ready
•
Freescale MC13192 RF Transceiver IC
•
Freescale MC9S08GT60 Microcontroller
•
Carrier-sense, multiple-access technology
•
Range: >700 feet, outdoor line of sight
•
Royalty-free USB drivers
•
USB interface programming as easy as RS232C
•
Agency approvals in place for immediate
deployment in the US, Canada, and Europe
•
16 Channels (2.405GHz to 2.480GHz)
•
Microcontroller pre-programmed with SIPP firmware
•
<35 microamp low-power mode
•
Antenna Integral to PCB Design–No External
Antenna to Purchase and Mount SIPP™ firmware
The DLP-RF1 combines a USB interface, Freescale™ MC13192 2.4GHz Direct-Sequence Spread Spectrum RF Transceiver IC and Freescale MC9S08GT60 microcontroller to form an
IEEE 802.15.4 compliant, ZigBee™ ready, short-range transceiver module.
The MC9S08GT60 microcontroller is preprogrammed with DLP Design’s Serial Interface Packet Processor (SIPP™ firmware) for accessing the transceiver functions via simple serial calls.
The application programming required for accessing the module via USB is functionally identical to that used to access the RS232C ports on a standard Windows/Linux/Mac PC via the
use of royalty-free Virtual COM Port (VCP) drivers. (No USB driver development is required for most applications.) The SIPP firmware in the DLP-RF1 resides at the application layer and
is based on Freescale’s SMAC. The SIPP firmware provides basic access to DLP-RF1 functionality: packet receive and transmit, transceiver settings, EEPROM access, etc.
DLP-RF2 - 2.4 GHZ OEM RF Transceiver Module
A 20-pin interface header is provided for each of these development tools to allow quick connection to the DLP-RF2 transceiver.
The DLP-RF2-SENS provides example designs for a temperature/humidity sensor, door switch input, and a system for measuring battery power. This developer’s tool demonstrates the low-power mode of operation in which the module
remains in Sleep Mode drawing less than 40 microamps of current from two AAA batteries until either the door switch input detects a change or the timer wakes up the transceiver to check in with the system controller.
The DLP-RF2-RELAY also demonstrates the low-power mode of operation while providing a battery power measurement system and door switch input together with two latching relays.
While in Sleep Mode, the total system current drawn from two AA batteries is less than 40 microamps regardless of the state of the relays.
The DLP-RF2-PROTO is intended to enable the designer to quickly progress in the development of hardware and software associated with wireless networking projects.
This board offers a number of flexible tools to accommodate numerous modes of operation:
DLP-RF2 Proto Board Features:
•
BDM Programming Interface
•
Easy-to-Use USB Interface for Modeling Serial Host Firmware on a PC
•
RS232C (DB9) Interface for Connection to a Legacy Peripheral
•
Buffered LED Indication of 8 Selected Digital I/O Lines
Price Each
1 50 100
DLP
Part No.
DLP-RF1 And Development Tools
DLP-RF2 (TTL Serial Interface)
DLP-RF1 (Host Interface)
250
The DLP-RF2 combines a Freescale™ MC13192 2.4GHz Direct-Sequence, Spread-Spectrum RF Transceiver IC and Freescale MC9S08GT60 microcontroller to form an IEEE 802.15.4
compliant, ZigBee™ ready, short-range transceiver module. The DLP-RF2 connects to user electronics via a standard, 20-pin male header.
The MC9S08GT60 microcontroller is preprogrammed with DLP Design’s Serial Interface Packet Processor
(SIPP™ firmware) for accessing the transceiver functions via simple serial calls. Interface to an external serial host microcontroller/DSP/FPGA, etc.
is accomplished via a simple 2-wire (RX, TX, and ground) interface.
The SIPP firmware in the DLP-RF2 resides at the application layer and is based on Freescale’s
SMAC. The SIPP firmware provides basic access to DLP-RF2 functionality: Packet receive and transmit, transceiver settings, EEPROM access, etc. The DLP-RF2 can also operate without a
serial host controller. Basic digital I/O, A/D conversions, temperature measurement, and latching/non-latching relay control are available via the SIPP firmware. The MC9S08GT60 can be
reprogrammed (if desired) with user-supplied firmware via a 6-pin BDM header that is compatible with the P&E USB-ML-12 and device programmers (purchased separately).
DLP-RF2 Development Tools
626-DLP-RF2-Z DLP-RF2-Z 35.00 30.00 27.00 25.00
DLP 802.15.4/ZIGBEE™ READY MODULES
•
Low-Power Mode Jumper
•
Prototyping Breadboard
•
Three Power Sources: USB Port, DC Jack (4-15VDC), or 9-Volt Battery Clips
•
A/D and Voltage Reference Setups
The DLP-RFID1 is a low-cost, USB-powered module for reading from and writing to ISO 15693, ISO 18000-3, and Tag-it™ intelligent RFID transponder tags. It has the ability to
both read and write up to 256 bytes of data in addition to reading the unique identifier (UID/SID). All of the DLP-RFID1’s electronics and antenna reside within the compact unit,
and all operational power is taken from the host PC via the USB interface. The range of the internal antenna is up to 4 inches depending upon the size of the tag being read.
Features:
•
ISO 15693, 18000-3, Tag-it™ HF-I Compatible
•
Read UID/SID of Up to 15 Tags Simultaneously
•
13.56MHz Reader/Writer
•
Built-in Antenna: Up to 4-Inch Read Range
•
FCC/IC/CE Modular Approval in Place
•
Permanent Unique Serial Number Accessible Via USB
•
Integrated Pass/Fail Beeper
•
USB Port Powered from Host PC (USB 1.1/2.0 Compatible)
•
USB Drivers Provided for Windows XP, XPx64, Server2003, 2000, 98, ME
•
Software Development Library Support for Visual C++/Visual Basic
Applications:
•
Real-Time Security
•
Personal Identification
•
Pharmaceutical Tracking
•
Inventory/Asset Management & Tracking
DLP-RFID1 RFID READER AND WRITER
Specifications:
•
Reader Frequency: 13.56MHz
•
Output Power: 200mW MAX
•
Range (Integral Antenna): 4 Inches MAX
•
Tags/Protocols Supported: Tag-It*, ISO18000-3, ISO15693
•
Communications Interface: USB 1.1/2.0 Compatible, Mini-B 5-Pin Connector
•
Operational Power – Active: 120mA
•
Operational Power – Idle: 15mA
•
Antenna: On-Board Antenna, SMA Position Available**
•
USB Driver Support: Windows XP, XPx64, Server2003, 2000, 98, ME
•
Physical Dimensions – OEM PCB: .20x2.17x3.12” typ. (5.1x55.1x79.3mm)
•
Physical Dimensions – Retail Enclosure: .83x2.3x3.25” typ. (21.1x58.4x82.6mm)
•
Operating Temperature: 0-70°C
MOUSER
STOCK NO.
Description
For quantities of 500 and up, call for quote.
Price Each
110
DLP
Part No.
•
Library/Book Management & Tracking
•
Baggage Tagging
•
Sports Event Timing
626-DLP-RFID1-RG DLP-RFID1-RG Includes reader, retractable USB cable and an assortment of tags 119.95 117.00
626-DLP-RFID1-OG DLP-RFID1-OG OEM Board Only 94.50 89.50
626-DLP-RFIDTAG DLP-RFIDTAG 30 Pack of RFID Peel and Stick Tags 29.95 27.50
OEM Version
Retail Version
Products may be RoHS compliant.
Check mouser.com for RoHS status.
© Copyright 2007 Mouser Electronics
© Copyright 2007 Mouser Electronics
NEXT
BACK
NEXT
BACK
© Copyright 2007 Mouser Electronics
© Copyright 2007 Mouser Electronics
NEXT
BACK
NEXT
BACK
Mouser Catalog Download