Instruction manual

ManualsBrandsR-Tech ManualsIndustrialTIG315

• Never lubricate the cylinder valve with oil or grease.

• Never allow an electrode to touch a cylinder!

• Do not expose cylinders to excessive heat, sparks, molten

slag or flames.

• Do not tamper with the cylinder valve.

• Do not try to loosen tight valves by means of a hammer,

a wrench, or any other object.

B) PRESSURE REGULATORS

• Keep pressure regulators in good condition. Damaged

regulators may cause damages or accidents. They should

be repaired by skilled personnel only.

• Do not use regulators for gases other than those for which

they were manufactured.

• Never use a leaking or damaged regulator.

• Never lubricate regulators with oil or grease.

C) HOSES

• Replace hoses which appear to be damaged.

• Keep hoses unwound in order to prevent kinks.

• Keep the excess hose neatly wound and out of the working

area in order to avoid damage.

• Cylinder fittings should never be modified or exchanged.

1.2.5 Radiation

Ultra-violet radiation emitted by arc rays may

damage your eyes and burn you skin. Therefore:

• Wear proper clothing and helmet.

• Do not use contact lenses!! The intense heat created

by the arc may cause them to stick to the cornea.

• Use a mask or helmet equipped with lens shades that have

a minimum DIN rating of 10

• Warn people in the area surrounding the welding sight that

you are going to be welding.

Remember: the arc may dazzle or damage the eyes. It is

considered dangerous up to a distance of 15 meters (50

feet). Never look at an arc with the naked eye.

• Prepare the welding area so as to reduce the reflection

and transmission of ultra-violet radiation: paint walls and

exposed surfaces in black to reduce reflection, install

shielding systems or curtains to reduce the transmission

of ultra-violet rays.

• Replace protective lenses whenever damaged or broken.

1.2.6 Electric shock

Electric shocks are hazardous and potentially fatall!!

• Do not touch live electrical parts.

• Insulate yourself from the workpiece and the

ground by wearing insulated gloves and clothing.

• Keep garments (gloves, shoes, hats, clothing) and body

dry.

• Do not work in humid or wet areas.

• If you are welding near a body of water take precautions

to ensure that the machine cannot fall into the water.

• Avoid touching or holding the workpiece by hand.

• Should you work in a dangerous area or close to one , use

all possible precautions.

• Stop welding immediately if you should feel even the

slightest sensation of electric shock. Do not use the

machine until the problem is identified and corrected.

• Often inspect the mains input cable.

• Disconnect the power input cable from the mains supply

before replacing cables or before removing the unit covers.

• Do not use the unit without protection covers.

•Always replace any damaged parts withGENUINECEBORA

SPARE PARTS.

• Never disconnect any of the unit's safety devices.

• Make sure that the mains power supply line is equipped

with a good electrical ground.

• Servicing of the machine must be done by qualified

personnel who aware of the risks involved with the high

voltage levels necessary to make the machine operate.

1.2.7 Pacemaker

Magnetic fields created by the high currents in the weld

circuit can affect pacemaker operation. Persons wearing

electronic life support equipment (pacemakers) should

consult their doctor before going near any arc welding,

gouging, cutting, or spot welding equipment in operation.

1.2.8 Noise

These power sources alone do not produce noise levels

exceeding 80 dB. The AC TIG welding procedure,

however, may produce noise levels in excess of 80

dB in which case the machine take operator must

take the necessary safety precations as prescribed

by the national take safety regulations.

2 GENERAL TECHNICAL DESCRIPTIONS

2.1 SPECIFICATIONS

These machine are constant current power sources, suitable

for both the TIG and Manual Metal Arc welding procedures.

These technologically advanced, high quality power sources

incorporate, single current adjustment range, square wave

technology and total central of the welding current.

Upon receiving and unpacking the machine, make a careful

inspection to ensure that there are no damaged parts. Should

there be a claim for losses or damages it must be made by the

purchaser directly to the shipper who handled the goods.

When requesting information about this welding machine

please state the machine’s part number and serial

number to ensure receiving accurate information relating

to your machine.

2.2 DESCRIPTION OF TECHNICAL SPECIFICATIONS

X-- -

---

-- -

-/---/-

PROTEZIONE TERMICA

THERMAL PROTECTION

PROTECTION THERMIQUE

TERMISCH GESCHÜTZ

PROTECCION TERMICA

VENTILAZIONE FORZATA

FORCED VENTILATION

VENTILE

KUHLART F

VENTILACION

IP 21

N˚

EN 60 974-1

50/60

I. Cl.

MADE IN ITALY