Owner`s manual

17
REV 4 0811041514
No. L-A2-02908
1. STOP! Read the safety information above
2. Turn 'OFF' any electrical appliance (such as the
Peterson warm air circulator) if used with the log
set.
1. Turn off all electric power to the warm air circulator (where used) if service is to be performed.
2. Put the switch in 'OFF' position (see 7 above). Log set will extinguish and pilot will go out.
1. Press 'O' (= OFF)
when complete shutdown is
desired.
Figure 22
2. Press 'I' (= Ignite)
After a series of rapid sparks the
pilot will light. When pilot is stable,
the main burner will ignite.
1. LIGHTING - Check the switch (marked "I" = Ignite; "O" = Off)
located on top of the decorative Pine Cone is set to "O" . Wait 5
minutes for gas to clear out.
* We recommend that before you install your log set you familiarize yourself with the control valve layout. This will
help you to be confi dent operating the log set when fully installed (see Figures below for typical control positions).
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fi re or explosion may
result causing property damage, personal injury or loss of life.
The Peterson Real-Fyre gas log set has a pilot which
must be lit by hand. When lighting the pilot, follow
these instructions exactly.
1. BEFORE LIGHTING, smell all around the gas
log set area for gas. Be sure to smell next to
the fl oor because some gas is heavier than air
and will settle on the fl oor.
WHAT TO DO IF YOU SMELL GAS
• Open a window.
• Do not try to light the appliance.
• Do not touch any electrical switch, do not
use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the
fi re department.
2. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will
not push in or turn by hand, don't try to repair it.
Call a qualifi ed, professional service technician.
Force or attempted repair may result in fi re or
explosion.
3. Do not use the gas log set if any part has
been under water. Immediately call a qualifi ed,
professional service technician to inspect the
gas log set and to replace any part of the control
system and any gas control which has been
under water.
LIGHTING INSTRUCTIONS 01(P) VALVE
3. Check the switch (marked "I" = ignite; "O" = "Off")
located on top of the decorative pine cone is set
to 'O'. Do not force.
4. Wait fi ve (5) minutes to clear out any gas. If you
then smell gas, STOP! Follow "1" in the safety
information above. If you don't smell gas, go to
the next step.
5. Press the switch ("I" = IGNITE) on the top of
the decorative pine cone. This transmits a rapid
series of sparks at the pilot head. These sparks
cease when the pilot fl ame is lit and stable. The
pilot is located at the rear right corner of the
burner (see Item 14 Part List on page 6). After
a short time the pilot will light the main burner.
CAUTION: IF THE GAS SET DOES NOT IGNITE
WITHIN 20 SECONDS, STOP, TURN
THE SWITCH TO "OFF", WAIT 5
MINUTES THEN REPEAT STEPS
3-6
• Normally, the pilot should remain lit. If it goes
out, repeat step 3 through 6.
• If the pilot will not stay lit after several tries, turn
the pine cone switch to 'OFF' (Figure 22) and
call your service technician or gas supplier.
6. Periodically check the pilot fl ame for proper fl ame
pattern (Figure 20).
7. To turn the set 'OFF', press the ("O"= OFF) switch
on top of the pine cone. The gas fl ow will cease
and all fl ames will go out.
TO TURN OFF THE GAS LOG SET
If this unit was shipped with a remote, or if a remote system was installed later, read and follow the separate
remote instructions to operate the burner remotely.