Owner`s manual

19
LIGHTING INSTRUCTIONS FOR YOUR MILLIVOLT GAS VALVE SYSTEM
1. STOP! READ THE SAFETY INFORMATION
CONTAINED IN THIS MANUAL ON P. 1.
2. Turn the control switch, wall switch, or remote
switch to the OFF position, or set the thermostat
in the lowest possible setting.
3. Push in the control knob (Fig. 19-1) and turn
clockwise
to the OFF position.
4. Smell for gas, especially near the fl oor. If you smell
gas, STOP! Follow B in the safety information on
this page. If you don’t smell gas, go to the next
step.
5. Push and turn control knob counterclockwise
to PILOT.
6. Push in on the control knob all the way and hold in.
Immediately light the ODS pilot or press in ignitor
button (Fig. 19-2) to light ODS pilot. Continue
to hold the control knob in for approximately 30
seconds after the ODS pilot is lit. Release the
knob, and it will pop back out. The ODS pilot
should remain lit. If it goes out, repeat steps 5
through 6.
• If knob does not pop up when released,
stop and immediately call your service
technician or gas supplier.
• If the ODS pilot will not stay lit after several
tries, follow the instructions TO TURN OFF
GAS TO APPLIANCE in your Owner’s Manual
and call your service technician or gas
supplier.
7. Push and turn the gas control knob
counterclockwise
to the ON position.
Your Real-Fyre
®
unvented gas log set is now ready for
you to enjoy. Simply fl ip the control switch (Fig. 19-1)
to the ON position. Then adjust the fl ame-height control
knob as desired.
When you are fi nished enjoying your Real-Fyre
®
log
set, fl ip your control switch (Fig. 19-2) to the OFF
position.
If total shutdown is desired, push the millivolt control
knob in slightly and turn to the OFF position (Fig. 19-1).
Your ODS pilot light will be extinguished.
When shutting your log set down, be sure to TURN
THE FLAME COMPLETELY TO THE OFF POSITION.
Allow the burner to remain completely off for 1
minute before relighting!
LIGHTING INSTRUCTIONS - SERIES 12 VALVE
FOR YOUR SAFETY, READ BEFORE LIGHTING
The Real-Fyre
®
gas log set has an ODS pilot that must
be lit by hand. When lighting the ODS pilot, follow these
instructions exactly.
A.
BEFORE LIGHTING, smell all around the gas
log set area for gas. Be sure to smell next to the fl oor,
because some gas is heavier than air and will settle
on the fl oor.
B. WHAT TO DO IF YOU SMELL GAS
• Open a window.
• Do not try to light the appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fi re
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don’t try to repair it. Call a qualifi ed
professional service technician. Force or attempted
repair may result in fi re or explosion.
D. Do not use the gas log set if any part has been
submerged in water. Immediately call a qualifi ed
professional service technician to inspect the gas
log set and to replace any part of the control system
and any gas control that has been underwater.
WARNING: If you do not follow these instructions exactly a fi re or explosion may result, causing
property damage, personal injury, or loss of life.
Manual
valve
system
ODS pilot
Piezo ignitor -
Press and release ignitor until
ODS pilot lights while depressing
the ODS pilot control knob.
ODS
pilot and
fl ame
height-
control
knobs
Millivolt valve
control knob
Operating
positions
OFF
PILOT
ON
Fig. 19-1
Control
switch
Millivolt gas valve control knob
operating positions
Read setting here
ON
OFF
PILOT
Fig. 19-1
Fig. 19-2