Owner`s manual

22
1. Using remote handset, turn main burner off by pressing "DOWN" button. Pilot will remain lit.
2. If complete shutdown is desired, WHEN THE LOG SET IS COOL, push in the ignitor knob and turn clockwise
to the "OFF" position. Replace the radiant heat shield.
FOR YOUR SAFETY, READ BEFORE LIGHTING
The Real-Fyre G46 Series gas log set has a pilot which can be lit by hand using the piezo ignitor. When lighting
the pilot, follow these instructions exactly.
BEFORE LIGHTING, smell all around the gas log set area for gas. Be sure to smell next to the fl oor as some
gas is heavier than air and will settle on the fl oor. IF YOU SMELL GAS, FOLLOW THE INSTRUCTIONS ON
PAGE 1.
Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn
by hand, don't try to repair it. Call a qualifi ed, professional service technician. Force or attempted repair may
result in fi re or explosion.
* We recommend that before you install your log set you familiarize yourself with the control valve layout. This will help
you to be confi dent operating the log set when fully installed (see Figures on page 16-23 for typical control positions).
WARNING: If you do not follow these instructions exactly, a fi re or explosion may result causing
property damage, personal injury or loss of life.
LIGHTING INSTRUCTIONS FOR G46-15 GAS LOG SET
1. STOP Read the safety information above.
2. Turn "OFF" any electrical appliance (such as the Peterson warm air circulator or any remote control system) if
used with the log set.
3. Push in ignitor control knob, turn clockwise
to "OFF" position (Figure 25). Turn variable fl ame height
control clockwise
to "OFF" position.
4. Wait fi ve (5) minutes to clear out any gas. If you then smell gas, STOP! Follow the safety information above. If
you don't smell gas, go to the next step.
5. Locate the pilot. Follow the metal tube from the gas control. Pilot is located at the right rear of burner pan.
6. To light pilot, turn ignitor knob from "OFF" position clockwise towards "IGN" until reaching stop. Press ignitor
knob in and hold for 5 seconds (only pilot gas will fl ow).
7. Continue holding knob in, turn the ignitor control knob to "PILOT" to activate the piezo ignitor (you should hear
a click, pilot should light). Continue to hold ignitor knob in for 30 seconds after pilot is lit. Release ignitor knob
and it will pop back up. The pilot should remain lit. If it goes out, repeat steps 5 through 8.
• If the knob does not pop up when released, stop and immediately call your service technician or gas supplier.
• If the pilot will not stay lit after several tries, turn the gas control knob to "OFF" and call your service technician
or gas supplier.
8. Turn ignitor knob counterclockwise
to "ON".
9. With the pilot lit, turn the fl ame height control towards "ON" (counterclockwise
) to desired fl ame height
and heat output. NOTE: When the unit has been burning for some time, use your remote control to adjust the
fl ame height and to turn the unit off.
10. If an electrical appliance is used with the log set, turn on or reconnect that appliance.
TO TURN OFF THE GAS LOG SET
TO TURN OFF THE GAS LOG SET
Figure 25
Ignitor Knob
Flame Height
Control Knob
2. Turn dial to "IGN",
push in and turn to "PILOT"
position. Press knob in and
hold for 60 seconds while
lighting pilot.
OFF PILOT ON
3. Turn knob to
"ON". To light burner
turn variable fl ame
height knob towards
"ON"
1. Use "OFF"
when complete shut-
down is desired.
4. When log set is
hot, press "DOWN"
on handset to turn off
main burner. Pilot will
remain lit.
NOTE: Press "UP" or
"DOWN" on handset to
adjust fl ame height as
desired.
1. LIGHTING - turn all knobs
to "OFF" and wait 5
minutes before lighting.