Owner`s manual

ManualsBrandsR.H. Peterson ManualsBurnerG46-30-15P

Robert H. Peterson Co.

Models

G46-18/20-01(P)

G46-18/20-11(P)

G46-18/20-15(P)

G46-18/20(P)

G46-24-01(P)

G46-24-11(P)

G46-24-15(P)

G46-24(P)

G46-30-01(P)

G46-30-11(P)

G46-30-15(P)

G46-30(P)

RHP

OWNER’S

MANUAL

No.L-A2-21506

REV 2 0603020800

ROBERT H. PETERSON CO. 14724 East Proctor Ave., City of Industry, CA 91746

Your Peterson Real-Fyre Gas Log Set is to be installed

only in a solid-fuel burning ﬁ replace with a working ﬂ ue

constructed of noncombustible material. Solid fuels

shall not be burned in a ﬁ replace where this gas log

set is installed. The installation, including provisions

for combustion, ventilation air and required minimum

permanent vent opening, must conform with the National

Fuel Gas Code (ANSI Z21.60a-2003 and CSA 2.26a-

2001) and applicable local building codes. In Canada,

the installation must conform with the current CAN/

CGA B149.1, and B149.2 Installation Code.

Z223.1)

and applicable local building codes. A damper clamp

is included to maintain the minimum permanent vent

opening and to prevent full closure of the damper

blade. The chimney damper MUST be fully open

when burning the log set. Your log set is designed

to burn with yellow ﬂ ames; adequate ventilation

is absolutely necessary.

Installation and service must be

performed by an NFI Certiﬁ ed or other

qualiﬁ ed, professional installer, service

agency or the gas supplier.

IMPORTANT: To comply with certiﬁ cation, listings,

and building codes, and for safe operation and

proper performance, ONLY Peterson parts and

accessories MUST be used with this gas log set.

IMPORTANT: READ THESE INSTRUCTIONS

CAREFULLY BEFORE STARTING

INSTALLATION OF YOUR LOG SET

- Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS.

• Open a window.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from

neighbor's phone. Follow the gas

supplier's instructions.

• If you cannot reach your gas supplier,

call the ﬁ re department.

WARNING: If the information in this

manual is not followed exactly, a ﬁ re or

explosion may result causing property

damage, personal injury or loss of life.

G46 SERIES BURNER

INSTALLER & CONSUMER :

These Instructions MUST be

retained with this appliance

C.S.A. CERTIFIED

GLOWING EMBERS

GAS FIREPLACE

LOG SET

Summary of content (26 pages)

PAGE 1
OWNER’S MANUAL Robert H. Peterson Co. RHP Models G46-18/20-01(P) G46-18/20-11(P) G46-18/20-15(P) G46-18/20(P) C.S.A. CERTIFIED GLOWING EMBERS GAS FIREPLACE LOG SET G46-24-01(P) G46-24-11(P) G46-24-15(P) G46-24(P) G46-30-01(P) G46-30-11(P) G46-30-15(P) G46-30(P) G46 SERIES BURNER WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
PAGE 2
Robert H. Peterson Co. RHP Models G46-18/20-01(P) G46-30-01(P) G46-18/20-11(P) G46-30-11(P) G46-18/20-15(P) G46-30-15(P) G46-18/20(P) G46-30(P) MANUEL OWNERS C.S.A.
PAGE 3
G46 GAS LOG SET TABLE OF CONTENTS PAGE # 1-2 TOPIC Cover - Important Safety Warnings Table of Contents 3 Burner - Parts Lists: General Burner and Log Parts List G46 Manual Valve System G46-11 Remote Valve System G46-01 Electronic Valve System G46-15V Remote Valve (Variable flame) System 4 5 5 6 6 Important Information: General information Technical Data Table Minimum Damper Opening Data 7 Installing your gas log set: Damper clamp Installation Installation of the burner Special Instructions for G46-01
PAGE 4
PARTS LIST FOR REAL-FYRE G46 SERIES GLOWING EMBER GAS LOG SETS Log styles, sizes and parts will vary depending upon the G46 Series model ordered. When ordering replacement parts, be sure to indicate your log set model. NOTE: Only the logs for the WO-24 Woodland Oak 24" Set are illustrated and listed below. Description 1. 2. 3. 4. 5. 6. 20" rear log 24" front log 15" top left log 15" top right log 9" top left log 9" top right log 7. 8. 9. 10. 11. 12. 13.
PAGE 5
SAFETY CONTROL SYSTEM FOR G46 MANUAL PILOT ASSEMBLY (Rear view) CERAMIC ELECTRODE (ITEM 21) LOCATION OF ORIFICE 19 PILOT ASSEMBLY (ITEM 20) Item No. 17. 18. 20 19. 20. 21. 22. 22 17 Description Safety control valve Pressure regulator (natural gas) Pressure regulator (L.P. gas) Handle assembly Pilot assembly Ceramic electrode Adapter elbow G46 Burner showing valve layout under heat shield (rear view). 18 NOTE: DO NOT REMOVE HEAT SHIELD SAFETY CONTROL SYSTEM FOR G46-11(P) 23 Item No.
PAGE 6
SAFETY CONTROL SYSTEM FOR G46-01(P) 26 25 Item No. G46 Burner showing Remote Control layout under heat shield. Description 25. 26. Safety control valve Pilot assembly NOTE: DO NOT REMOVE HEAT SHIELD SAFETY CONTROL SYSTEM FOR G46-15(P) Item No. 28 27. 28. Description Safety control valve Pilot assembly 27 G46 Burner showing 15 valve under heat shield.
PAGE 7
G46 SERIES IMPORTANT INFORMATION Do not use this log set if any part has been under water. Immediately call a qualified professional service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. A fireplace screen must be in place when the log set is burning. Provisions for adequate combustion air must be maintained. Combustion air is adequate when all flames curl into the fireplace and away from the screen.
PAGE 8
DAMPER STOP CLAMP INSTRUCTIONS DAMPER CLAMP INSTRUCTIONS The damper clamp with hex bolt (Figure 1) is provided as a means to prevent full closure of the damper blade. The clamp is easily attached to most damper blades with pliers or wrench, and must be permanently installed. The clamp is designed to prevent accidental closure of the damper when installed as illustrated (Figures 2 A&B).
PAGE 9
INSTALLING YOUR REAL-FYRE GAS LOG SET (Continued) NOTE: REFER TO PARTS LIST (PAGE 4) WHEN FOLLOWING THESE INSTRUCTIONS. INSTALLATION OF LOG SET IN YOUR FIREPLACE (be sure the gas to the fireplace is off) 1. The burner gas inlet is located in front of the gas 3. Position the burner in the center rear of the fireplace. valve (Figure 3). Use teflon tape or pipe compound Connect the connector kit tubing (Item 16) to your gas on all pipe thread male connections, except where supply.
PAGE 10
INSTALLING YOUR REAL-FYRE GAS LOG SET (Continued) SPECIAL INSTRUCTIONS FOR G46-01-xx(P) MODELS Installing pine cone with switch for 01M models CONNECTING THE IGNITION PACK TO THE G46-01(P) VALVE The G46-01-xx(P) valve comes complete with the wiring harness connected to the pine cone switch. You may wish to ensure it is correctly connected before finally connecting the 3 wires to the valve as below. TO CHECK THE WIRING ASSEMBLY: Figure 5 CHECK CONNECTIONS A.
PAGE 11
INSTALLING YOUR REAL-FYRE GAS LOG SET (Continued) IMPORTANT For all valves, the air MUST be purged from the gas line before the pilot will light and burn properly. The time needed to purge will depend on the length of the gas line to the unit and the amount of time since the unit or gas line was last used. It may take several minutes before all the air is purged and the pilot will light and burn properly. Follow the "Lighting Instructions" (pages 16-23) in this manual.
PAGE 12
INSTALLING YOUR REAL-FYRE GAS LOG SET (Continued) Note: For Charred Series see Page 14 For Western Campfyre Series see Page 15. Proper log placement is important to insure proper performance of your Real-Fyre gas log set. Be sure to follow the log placement instructions carefully. 3 optional log placement patterns, an exclusive feature of Real-Fyre gas logs, are explained below. Figure 9 REAL-FYRE GAS LOG SETS 18"-30". 1 24" Woodland Oak (WO) log set shown. For all Options - Step 1.
PAGE 13
INSTALLING YOUR REAL-FYRE GAS LOG SET (Continued) Figure 11 REAL-FYRE GAS LOG SETS OPTIONAL BONUS LOG PLACEMENT Your optional bonus log (included with Golden Oak Designer Plus and Split Oak Designer Plus Log Sets) should be placed directly above the front or rear bottom logs (Logs #1 & #2), so it does not extend into the space between the front and rear logs, as shown in Figure 11.
PAGE 14
INSTALLING YOUR REAL-FYRE GAS LOG SET (Continued) If you have purchased this style of log set, follow the instructions below. NOTE: The logs for the CHD Charred Oak Set are illustrated. Log styles and sizes will vary depending upon the Charred Series log set ordered. NOTE: INSTRUCTIONS ON THE FYREBED MAY NOT BE APPLICABLE The COALS FYREBED (see Figure 13) supplied with your Charred log set, fits onto the back of the burner pan.
PAGE 15
INSTALLING YOUR REAL-FYRE GAS LOG SET (Continued) WESTERN CAMPFYRE STYLE LOGS LAYOUT SUMMARY If you have purchased this style of log set, follow the instructions below. 1 6 2 5 4 8 3 7 9 Figure 19 WESTERN CAMPFYRE 24 1. MWCFL-18BR 2. MWCFL-18L 3. MWCFL-18R 4. MWCFL-13T 5. MWCFL-13TY REAR LOG LEFT LOG RIGHT LOG TOP LOG TOP LOG ITEMS 6. MWCFL-10TY 7. MWCFL-8T1 8. MWCFL-11T 9.
PAGE 16
FOR YOUR SAFETY, READ BEFORE LIGHTING * We recommend that before you install your log set you familiarize yourself with the control valve layout. This will help you to be confident operating the log set when fully installed (see Figures on page 16-23 for typical control positions). WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
PAGE 17
POUR VOTRE SECURITE, LISEZ AVANT D’ALLUMER * Nous recommandons qu’avant que vous installiez votre grosse bûche mise vous vous familiarisez avec la disposition de la valve du contrôle. Cela vous aidera pour être opérer plus confiant la grosse bûche mise quand a complètement installé (voyez des Illustrations dessous pour contriol typique placez).
PAGE 18
FOR YOUR SAFETY, READ BEFORE LIGHTING * We recommend that before you install your log set you familiarize yourself with the control valve layout. This will help you to be confident operating the log set when fully installed (see Figures on pages 16-23 for typical control positions). WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
PAGE 19
POUR VOTRE SECURITE, LISEZ AVANT D’ALLUMER * Nous recommandons qu’avant que vous installiez votre grosse bûche mise vous vous familiarisez avec la disposition de la valve du contrôle. Cela vous aidera pour être opérer plus confiant la grosse bûche mise quand a complètement installé (voyez des Illustrations dessous pour contriol typique placez).
PAGE 20
FOR YOUR SAFETY, READ BEFORE LIGHTING * We recommend that before you install your log set you familiarize yourself with the control valve layout. This will help you to be confident operating the log set when fully installed (see Figures on page 16-23 for typical control positions). WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
PAGE 21
POUR VOTRE SECURITE, LISEZ AVANT D’ALLUMER * Nous recommandons qu’avant que vous installiez votre grosse bûche mise vous vous familiarisez avec la disposition de la valve du contrôle. Cela vous aidera pour être opérer plus confiant la grosse bûche mise quand a complètement installé (voyez des Illustrations dessous pour contriol typique placez).
PAGE 22
FOR YOUR SAFETY, READ BEFORE LIGHTING * We recommend that before you install your log set you familiarize yourself with the control valve layout. This will help you to be confident operating the log set when fully installed (see Figures on page 16-23 for typical control positions). WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
PAGE 23
POUR VOTRE SECURITE, LISEZ AVANT D’ALLUMER * Nous recommandons qu’avant que vous installiez votre grosse bûche mise vous vous familiarisez avec la disposition de la valve du contrôle. Cela vous aidera pour être opérer plus confiant la grosse bûche mise quand a complètement installé (voyez des Illustrations dessous pour contriol typique placez).
PAGE 24
PILOT BURNER ADJUSTMENT (G46 MANUAL) is necessary, the following steps should be taken: With the pilot burner lit and the control knob in the pilot position, use a long narrow screwdriver to turn the pilot adjustment screw (located on front of valve). Turn the adjustment screw slowly clockwise to reduce the flame, or counterclockwise to increase the flame. The adjustment screw can be turned so that the pilot flame is completely extinguished.
PAGE 25
FLAME PATTERN ADJUSTMENT (ALL MODELS) To adjust the flame pattern, take a long blade screwdriver or similar tool and stir the granules until the desired pattern is achieved. DO NOT REMOVE GRANULES FROM THE BURNER PAN. Long bladed screwdriver (or similar) Insert blade into sand and stir granules in various places until desired flame pattern is achieved. MAINTENANCE: Periodically remove the logs and examine the burner assembly. If dirty, clean with a stiff brush. Also examine the area around the pilot.
PAGE 26
WARRANTY PETERSON VENTED GAS LOG SETS LIMITED WARRANTY All Peterson Gas Logs are WARRANTED for as long as you own them (Lifetime). All Peterson Burner Assemblies are WARRANTED for TEN (10) YEARS. SPK-26 controls are covered by a THREE (3) YEAR “All Parts” Warranty. All other Peterson Valves, Pilots and Controls are covered by a ONE (1) YEAR Limited Warranty (excluding batteries).