Owner`s manual

23
LIGHTING INSTRUCTIONS - SERIES 16 VALVE
Do not use this appliance if any part has been underwater. Immediately call for a qualifi ed professional service technician
to inspect the appliance and to replace any part of the control system and any gas control that has been underwater.
LIGHTING THE PILOT
1. Turn the burner control knob (Fig. 23-1) on the burner
control valve assembly on the side of the burner pan
counterclockwise so that the text on the top of the
knob changes from OFF to PILOT. (Only pilot gas will
fl ow when the knob is pushed in.)
2. While pushing in the knob and holding it, manually light
the pilot fl ame using a long fi replace match or long-tip
butane lighter.
3. Continue to press in and leave the burner control knob
in the PILOT position for 30 seconds after the pilot has
been lit to allow the thermocouple to detect the pilot
fl ame. Then release the knob. The pilot will stay lit.
Note: The pilot fl ame should always be present when
the burner system is in operation, and should just
envelop the tip of the thermocouple (see section
on pilot adjustment).
IGNITING THE MAIN BURNER
1. Verify that the pilot is lit and burning properly (Fig. 23-
2), then turn the burner control knob counterclockwise
so ON is at the top. This opens the valve and allows
gas to fl ow to the main burner once the ON/OFF switch
is turned ON.
2. Flip the ON/OFF switch to the ON position. This will ignite
the main burner.
SHUTTING OFF THE MAIN BURNER
1. Flip the ON/OFF switch to the ON position.This will shut
off the main burner.
2. Turn the burner control knob fully clockwise to the
OFF position.
SHUTTING OFF THE PILOT
If you do not plan on using your pan burner for an extended
period, you may elect to extinguish the pilot. To do this, rotate
the burner control knob to the OFF position (Fig. 23-1).
Note: This will require that you relight the pilot before
you use the burner again.
ADJUSTING THE PILOT
The pilot burner is preset at the factory. However, should
adjustment be necessary, the following steps should be
taken:
With the pilot burner lit and the control knob in the PILOT
position (Fig. 23-2), use a narrow screwdriver and turn
the pilot adjustment screw (located in the valve body) slowly
clockwise to reduce the fl ame, or counterclockwise
to increase the fl ame.
The adjustment screw can be turned so that the pilot fl ame is
completely extinguished. Some tightening of the adjustment
screw may occur during adjustment. This is normal. The pilot
fl ame should be a soft blue fl ame with yellow tipping that
encircles the thermocouple tip. Test the main burner by following
the main burner ignition instructions above.
If this unit was shipped with a remote, or if a remote system
was installed later, read and follow the separate remote
instructions to operate the burner remotely.
FOR YOUR SAFETY, READ BEFORE LIGHTING
ON
ON/OFF
switch
PILOT
OFF
Fig. 23-1
WARNING
If you do not follow these instructions exactly, a fi re or explosion may result, causing property damage, personal injury,
or loss of life.
The Real-Fyre
®
burner system has a pilot that can be lit by hand using a match or lighter. When lighting the pilot, follow
these instructions exactly.
BEFORE LIGHTING, smell all around the burner area for gas. Be sure to smell next to the fl oor, as some gas is heavier
than air and will settle on the fl oor. IF YOU SMELL GAS, FOLLOW THE INSTRUCTIONS ON P. 1. Use only your hand to
push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it. Call a
qualifi ed professional service technician. Force or attempted repair may result in fi re or explosion.
Fig. 23-2
Pilot adjustment