Owner`s manual

4
L-A2-041
REV 7 - 1302121321
HOW TO INSTALL THE G4 SEE-THRU GAS LOG SET
Note: This gas log set must be installed by an
NFI Certifi ed or other qualifi ed professional
installer. Instructions must be followed
carefully when installing to ensure proper
performance and full benefi t from the gas
log set.
Important: To comply with certifi cation, listings, and building code acceptances, and for safe operation
and proper performance of this log set, use ONLY Peterson Real-Fyre
®
parts and accessories.
Use of other controls, parts, and accessories that are not approved for use with Real-Fyre
®
gas log sets is prohibited and will void all warranties, certifi cations, listings, and building code
approvals, and may cause property damage, personal injury, or loss of life.
CONNECTING THE GAS SUPPLY
Note: DO NOT run the gas line between the two
burners. Running the gas line between the
burners may cause overheating of the gas
line and control valve (if equipped).
If your burner is to be installed with a pilot kit;
carefully follow the instructions supplied with your
pilot kit for specifi c gas connection.
1. Attach the small adapter (Item 7C) to the nipple,
using a pipe compound resistant to all gases.
Tighten securely. DO NOT REMOVE THE FUEL
INJECTOR / AIR MIXER. Then attach one end of
the fl ex connector (Item 7B) to the small adapter.
Tighten securely.
2. Be sure gas to the fi replace is off. Attach the large
adapter (Item 7A) to the gas-supply stub using a
pipe compound resistant to all gases. Tighten
securely. Then attach the open end of the fl ex
connector to the large adapter. Tighten securely.
Ensure the pans rests level on the fi replace fl oor
after connection. Adjust the pans if necessary.
3. Use a long-necked butane lighter, or lay a lighted
match next to the burner pipe, and carefully turn
on the gas supply until the burner ignites. Test at
all connections for leaks using the appropriate
soapy water solution. If bubbles appear, a leak
is present. Turn off the gas and tighten at all
connections. Repeat until no leaks are present. If
a leak persists, turn off the gas supply and contact
the local gas company or dealer. NEVER USE A
FLAME TO CHECK FOR LEAKS.
BURNER CONNECTION INSTALLATION
Check the PARTS LIST to be sure all parts are included
with the connection. Pipe compound resistant to the
action of propane gas must be used on all threaded
male connections, except brass to brass.
Refer to the PARTS LIST when completing the
following instructions.
1. Connect the
3
/
8
" x 6" pipe to the
3
/
8
" elbow.
Continue to connect the 6" nipple to the
3
/
8
" tee.
2. Connect the
3
/
8
" street elbow to the tee and
connect the
3
/
8
" x 1" nipple.
3. Once the fittings are assembled, continue to
connect the burner and fuel injector assembly
(Item #12) to the tee and elbow.
Rotate each burner pan to tighten the complete
assembly together. Ensure that all connections are
tight.
There should be an approximately 2" gap between the
burner pans after the connector kit has been installed
(Fig. 4-1). Once the assembly is completed, the burner
pan will look like Fig.4-2.
BURNER PLACEMENT
Make sure the gas to the fi replace is off. Be sure that
the fi replace fl oor is clear of any debris. Center the
burner assembly in the fi replace and check to see if it
lies lay fl at on the fl oor. Place the grate squarely over
the burner pans and install the stabilizer clips (Item
#4) to the grate bars so that the slots of the stabilizer
clips fi t over the back edge of the burner pans (see
Fig. 4-1). Use the nuts and bolts provided to secure
the clips in place. Remove the grate for gas connection
and granule placement.
Glowing Ember burner with fl ex connector kit
Fig. 4-3
Match
Flex connector
Connect to
gas supply
B URNER
PAN
B URNER
PAN
GRATE
STABILIZER
CLIPS
2"
Fig. 4-1
Side view
Stabilizer
clips
Grate
Burner pan
Burner pan
Approx.
Fig. 4-2 Top view