Owner`s manual
WARNING
If you do not follow these instructions exactly, a fi re or explosion may result, causing property
damage, personal injury, or loss of life.
LIGHTING INSTRUCTIONS - SERIES 15 VALVE
Do not use this appliance if any part has been underwater. Immediately call for a qualifi ed professional service technician
to inspect the appliance and to replace any part of the control system and any gas control that has been underwater.
Gas valve operating positions
OFF IGNITION PILOT ON
Fig. 25-1
Flame-height control knob
Fig. 25-4
Fig. 25-3
LIGHTING THE ODS PILOT
1. Turn the ignitor control knob (Fig. 25-1) on the burner
control valve assembly to the side of the burner pan
counterclockwise so that the narrowing part of the
knob moves from the OFF position, slightly toward IGN,
until reaching the stop.
2. Press the ignitor control knob in and hold in for fi ve
seconds (only ODS pilot gas will fl ow).
3. Continue pressing in while turning the ignitor control
knob further counterclockwise toward the PILOT
position, until you hear a click. The click is an indication
that the piezo ignitor has been activated.
Note: If the spark from the piezo ignitor does not light
the ODS pilot, repeat steps 2 & 3 until the ODS
pilot lights.
4. Continue to hold the ignitor control knob in the PILOT
position for 30 seconds after the ODS pilot has been lit to
allow the thermocouple to detect the ODS pilot fl ame.
Note: The ODS pilot fl ame should always be present
when the burner system is in operation, and should
just envelop the tip of the thermocouple.
IGNITING THE MAIN BURNER
1. When the ODS pilot fl ame is stable, release the ignitor
control knob and turn counterclockwise to the ON
position to enable the main burner.
2. Turn the flame-height control knob (Fig. 25-3)
counterclockwise
to the fully ON position
(Fig. 25-4) to ignite the burner at maximum BTU.
After the main burner ignites, adjust the fl ame height
as indicated below.
ADJUSTING THE FLAME HEIGHT
1. To adjust the fl ame, turn the fl ame-height control
knob (Fig. 25-3) counterclockwise to increase
the flame height, or clockwise to decrease
the fl ame height, until the fl ames have the desired
characteristics.
2. When you are fi nished enjoying your fi re, turn the
fl ame-height control knob to OFF. The ODS pilot will
remain lit. The burner system can be relit by rotating
the fl ame-height control knob toward ON.
SHUTTING OFF THE ODS PILOT
If you do not plan on using your burner system for an
extended period, you may elect to extinguish the ODS pilot.
To do this, rotate the fl ame-height control knob to the OFF
position and then rotate the ignitor control knob to the OFF
position (Fig. 25-1).
Important: When shutting your burner down, be sure
to TURN THE FLAME FULLY OFF (to
PILOT or OFF). Make sure the burner
is completely off for one minute before
relighting.
If this unit was shipped with a remote, or if a remote
system was installed later, read and follow the separate
remote instructions to operate the burner remotely.
FOR YOUR SAFETY, READ BEFORE LIGHTING
Ignition
control
knob
Flame-
height
control
knob
OFF ON
25
The Real-Fyre
®
burner system has an ODS pilot. When starting the ODS pilot, follow these instructions exactly.
BEFORE LIGHTING, smell all around the gas burner system area for gas. Be sure to smell next to the fl oor, as some gas
is heavier than air and will settle on the fl oor. IF YOU SMELL GAS, FOLLOW THE INSTRUCTIONS ON P. 1.
Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't
try to repair it. Call a qualifi ed professional service technician. Force or attempted repair may result in fi re or explosion.
Fig. 25-2
Thermocouple
Flame touching