User Manual
Table Of Contents
- Important Warnings
- Bio-Incompatibility Notice
- Compliance
- Introduction
- About this Guide
- Additional Detailed Documentation
- Contact Information
- Product Warranty
- Chapter 1
- Introduction
- Installation Checklist
- Installing Components
- Install the Central Server
- Install the Gateway
- Install Routers
- Place a Pendant into Survey Mode
- Determine Placement of Routers
- Quick Look Router
- Gateway/Router Reset Button
- LED Sequence
- Gateway/Router Channel Default
- Additional Gateway/Router Installation
- Changing Channels
- Router Depth
- Rebuild Subnet on Scanned Devices
- Scan Devices
- Chapter 2
- Introduction
- Transceiver Devices
- LED Light Indicator
- Installing Transceiver Devices
- Pull Cords/Emergency Call
- Check-in Pull Cord
- Pull Cord Transceiver with Extended Battery Pack
- Wall Mount Emergency Call
- Universal Transceiver
- Tamper
- Nurse Call
- Door/Window Transceiver
- Door/Window Transceiver with Reset Button
- PIR Sensor
- Smoke Detector
- Pendant Transceivers
- Activate the Battery
- Set up the Pendant
- Reset the Pendant
- Verify the Pendant Appears in the System
- Replace the Battery
- Test the System Operation
- Chapter 3
- Introduction
- Device Failure
- Router Failure
- Gateway Failure
- Chapter 4
- Specifications
- Power Cable Run Lengths
- Mesh Network Router/Gateway
- Quick Look Display for Quick Look Router
- Pendant Transceiver
- Pull Cord
- Nurse Call
- Door/Window Transceiver
- PIR Sensor
- Smoke Detector
- Universal Transceiver
Chapter 2: Installing Transceiver Devices
34 9600 Series Wireless Call System (0510-1078-D) - Hardware Installation Guide
Door/Window Transceiver
A Door/Window transceiver is used to protect a door or window against
unauthorized egress. An Exit alarm event is reported in the Event List when a
monitored door or window is opened. The alarm automatically clears when the
door or window is closed. The Door/Window transceiver is supervised; if no
information is received by the system from the transceiver for a specified number
of minutes, a Device Fault alarm is generated in the Event List at the computer.
The Door/Window transceiver has one (1) LED light. The light is visible when
enclosure door is open (i.e. during installation), but not visible during normal operation when the enclosure
door is closed. The light flashes briefly once every check-in (20 minutes by default) and once each time the
device alarm is triggered or cleared. Green indicates communication with the Router is good; red indicates
communication failure and device is not able to transmit to the Router.
The Door/Window transceiver comes in two pieces: the transceiver enclosure and a magnet. The magnet is
attached directly to the door or window. The transceiver enclosure is mounted on the door or window frame
and can be mounting with the attached adhesive pad or a screw. An alarm triggers when the devices are
separated. The Door/Window transceiver is powered by a replaceable 3V battery within the Universal
enclosure.
To mount the Door/Window magnet to the door or window
1. Determine placement of the magnet. The distance between the reed switch in the transceiver and
the magnet must be no more than 1/2
inch.
2. Using the Door/Window transceiver magnet as a template, place it level against the door or
window and mark the location of the two mounting holes.
3. Drill holes where you made the marks.
4. Line up the holes on the magnet with the newly drilled holes and mount the magnet using the
screws provided.
NOTE: The Universal transceiver integrates with the Door/Window transceiver. Refer to
“Universal Transceiver” on page 29for information on the LED light, tamper
functionality and replacing the battery.
NOTE: When mounting the Door/Window magnet on a door, there is a better sensitivity
if the magnet is mounted closer to the opposite edge from the hinges.