Installation Guide
7
Installation Instructions
Pad size and anchoring methods should be chosen to meet wind loading requirements
in your area. Visit www.qwik.com for the most up-to-date engineering
documentation or to use our online pad selection tool.
Inspect Hardware Package Contents:
5010266_REV-E / 1201850001
Locate the ll port cap (corner nearest the product label) and ensure it is
securely pressed into pad and then tip the pad onto its corner where the plug is
located. This process should shift the powdered gelling agent contained inside
the pad towards the ll corner.
Place the QwikPad™ for Condensers on level, compacted ground where
equipment is to be installed (or on top of existing, level concrete pad).
Remove ll port cap. Insert garden hose into ll port and ll QwikPad™ for
Condensers to the top with tap water.
Do not overfill – Overfilling may result in loss of a portion of the gelling agent.
Replace ll port cap.
(Required for some installations)
Install ground or concrete anchors
as determined by your wind loading
requirements.
Place the equipment onto the
QwikPad™ for Condensers
and center.
Assemble four (4) condenser unit tie-down assemblies as shown below.
Insert tie-down assemblies into appropriate pad slots by angling
bottom retaining washer as shown and dropping into slot.
Slide tie-down assemblies inward
toward unit until L-bracket meets up
with unit. Tighten down ange nut on
tie-down assembly to secure it to the
QwikPad™ for Condensers.
Install two (2) self-tapping hex head
screws through each tie-down assembly
into base of unit, securing the unit to
the QwikPad™ for Condensers.
Here, the completed tie-down
assemblies are shown in-place,
attached with self-tapping hex
head screws to the condenser
unit, which is centered on the
QwikPad™ for Condensers.
1
2
3
4
5
6
8
9
10
QwikPad™ for Condensers
Ground Anchor (QT8110) Installation:
` Insert anchors into hole located on outer
edge of pad.
` Using a 1” wrench, turn the anchor
clockwise while pushing downward on
top of the anchor.
` Continue driving anchor down until
anchor head meets the pad.
Do not over-tighten.
` When using ground anchors, install
them on opposite sides (See example
at right).
` NEVER INSTALL AN ANCHOR IN THE
CENTER HOLE.
Concrete Anchor (QT8111) Installation:
` With pad in place, drill four (4) holes
in concrete to 1.375” minimum depth,
centrally located in anchor holes using
3/16” masonry bit (included in QT8111).
Center the drill bit in the anchor holes.
` Secure pad using four (4) 1/4” x 4”
concrete anchors with fender washers.
(included).
QwikPad “L” Bracket (4)
¼”-20 x 4” Carriage Bolt (4)
Builds (4)
Stainless Steel
Tie-Down
Assemblies
#10-16 x ¾” Self-tapping,
Hex Head Screw (8)
¼”-20 Serrated
Flange Nut (4)
Retaining Washer (4)
QwikProducts® is a registered trademark and QwikPad™ is a trademark of Mainstream Engineering Corporation® Rockledge, Florida 32955, (321) 631-3550, © 2020 Mainstream Engineering Corporation®
U.S. Patents #10,408,493,#10,559,742 and other Patents Pending
MADE IN THE USA
For more details or information about the QwikPad™ for Condensers
visit www.qwik.com/qwikpad4cond/, email info@qwik.com
or call 1-321-631-3550
Tie-down assemblies must be located one (1) per each side of the
unit or two (2) on two (2) opposing sides of the unit.