Brochure

QwikSwap®
The Low-Cost, Robust Alternative to Expensive Unreliable ECM Motors
It is impractical to have all the dierent variations of ECM motors on the truck, so a failed ECM blower motor typically
means a trip to the parts house and a few hours wasted.
Now you can have the solution on the truck and save money too.
QwikSwap® is a money saving solution that allows the replacement of a failed OEM ECM, X13® or SelecTech® Motor
with a lower cost, more reliable, Permanent Split Capacitor (PSC) motor, along with a capacitor.
There is a QwikSwap® board for every type of ECM motor...
and it is a solution you can have on the truck, and no custom programming is required. QwikSwap® boards operate
with any PSC motor up to 1 horsepower, either 120 or 240 VAC single phase.
QwikSwap® X1 (QT6101)
The basic QwikSwap® X1 (QT6101) provides a single technician-selected motor speed when
replacing a failed OEM Constant Torque ECM, X13® or SelecTech® motor. Installation is as easy
as moving wires from the failed ECM motor to the QwikSwap® X1 board, then connecting the
replacement PSC motor’s common and power lead to the QwikSwap® X1 board (along with a
capacitor).
Protected by U.S. Patents #9,417,005 & #9,207,001.
QwikSwap® X3 (QT6100)
QwikSwap® X3 (QT6100) provides replacement of a failed OEM Constant Torque ECM, X13® or
SelecTech® motor with Permanent Split Capacitor (PSC) motor while also ADDING performance
improving variable blower air ow capability - like high end systems have. Installation is
as simple as moving the wires from the failed ECM motor to the QwikSwap® X3 board, then
connecting the replacement PSC motor’s common and three power leads (one for each speed) to
the QwikSwap® X3 board (along with a capacitor).
Protected by U.S. Patents #9,417,005 & #9,207,001.
QwikSwap® V3 (QT6104)
QwikSwap® V3 (QT6104) provides replacement of a failed OEM Variable Air Flow Rate ECM
2.0. 2.3, 2.5 or 3.0 motor with a Permanent Split Capacitor (PSC) motor while maintaining
variable blower air ow capability. As with any QwikSwap, installation simply requires
moving wires from the failed ECM motor to the QwikSwap® V3 board, then connecting the new
PSC motor’s common and the three power leads (one for each speed) to the QwikSwap® V3
board (along with a capacitor).
Protected by U.S. Patents #9,417,005 & #9,207,001.
Optional Humidity Sensor (QT6001)
While QwikSwap® X3, QwikSwap® V3 and our QwikSEER+® WattSaver all provide variable blower air
ow leading to improved humidity removal, if humidly remains an issue these control boards have a
simple plug-in connection for this optional humidly sensor. When installed on the control board and
the relative humidity in the return air is measured to be greater than 50%, the control board control logic
changes from maximizing performance to maximizing moisture removal. Once the humidity drops to
below 50%, the control board returns to optimizing performance.
For more details or information about QwikSwap® visit www.qwik.com
MKTG000193_REV-E / 20210713
All marks shown within this document are properties of their respective owners, X13® is a registered Trademark of Regal Beloit®. SelecTech®,
Emerson®, U.S. Motors® and Nidec® are registered trademarks of Nidec Motor Corporation. QwikProducts® and QwikSwap® are registered
trademarks of Mainstream Engineering Corporation, Rockledge, Florida 32955, [phone] • © 2018 Mainstream Engineering Corporation •
All QwikProducts™ are made in the USA. Protected by U.S. Patents #9,417,005 & #9,207,001.
Mainstream Engineering Corporation®
1-800-866-3550
www.qwik.com
by Mainstream Engineering Corporation®
PROUDLY MADE
IN THE U.S.A.
QwikSwap
®