Product Overview

QwikSwap™
The Low-Cost, Robust Alternative to Expensive Unreliable ECM Motors
It is impractical to have all the dierent variations of ECM motors on the truck, so a failed ECM blower motor typically
means a trip to the parts house and a few hours wasted.
Now you can have the solution on the truck and save money too.
QwikSwap™ is a money saving solution that allows the replacement of a failed OEM ECM, X13® or SelecTech® Motor
with a lower cost, more reliable, Permanent Split Capacitor (PSC) motor, along with a capacitor.
There is a QwikSwap™ board for every type of ECM motor...
and it is a solution you can have on the truck, and no custom programming is required. QwikSwap™ boards operate
with any PSC motor up to 1 horsepower, either 120 or 240 VAC single phase.
QwikSwap™ X1 (QT6101)
The basic QwikSwap™ X1 (QT6101) provides a single technician-selected motor speed when
replacing a failed OEM Constant Torque ECM, X13® or SelecTech® motor. Installation is as easy
as moving wires from the failed ECM motor to the QwikSwap™ X1 board, then connecting the
replacement PSC motor’s common and power lead to the QwikSwap™ X1 board (along with a
capacitor).
QwikSwap™ X3 (QT6100)
QwikSwap™ X3 (QT6100) provides replacement of a failed OEM Constant Torque ECM,
X13® or SelecTech® motor with Permanent Split Capacitor (PSC) motor while also ADDING
performance improving variable blower air ow capability - like high end systems have.
Installation is as simple as moving the wires from the failed ECM motor to the QwikSwap™ X3
board, then connecting the replacement PSC motor’s common and three power leads (one for
each speed) to the QwikSwap™ X3 board (along with a capacitor).
QwikSwap™ V3 (QT6104)
QwikSwap™ V3 (QT6104) provides replacement of a failed OEM Variable Air Flow Rate ECM
2.0. 2.3, 2.5 or 3.0 motor with a Permanent Split Capacitor (PSC) motor while maintaining
variable blower air ow capability. As with any QwikSwap, installation simply requires
moving wires from the failed ECM motor to the QwikSwap™ V3 board, then connecting the
new PSC motor’s common and the three power leads (one for each speed) to the QwikSwap™
V3 board (along with a capacitor).
Optional Humidity Sensor (QT6001)
While QwikSwap™ X3, QwikSwap™ V3 and our QwikSEER+® WattSaver all provide variable blower air
ow leading to improved humidity removal, if humidly remains an issue these control boards have a
simple plug-in connection for this optional humidly sensor. When installed on the control board and
the relative humidity in the return air is measured to be greater than 50%, the control board control logic
changes from maximizing performance to maximizing moisture removal. Once the humidity drops to
below 50%, the control board returns to optimizing performance.
For more details or information about QwikSwap™ visit www.qwik.com
MKTG000193_REV-B / 2000828
All marks shown within this document are properties of their respective owners, X13® is a registered Trademark of Regal Beloit®. SelecTech®,
Emerson®, U.S. Motors® and Nidec® are registered trademarks of Nidec Motor Corporation. QwikProducts™ and QwikSwap™ are trademarks of
Mainstream Engineering Corporation® Rockledge, Florida 32955, [phone] • © 2016 Mainstream Engineering Corporation® •
All QwikProducts™ are made in the USA. Patents Pending
Mainstream Engineering Corporation®
1-800-866-3550
www.qwik.com
PROUDLY MADE
IN THE U.S.A.
QwikSwap
™