Submittal Sheet

QwikSEER+
WattSaverWattSaverWattSaver
QwikSEER+
WattSaverWattSaverWattSaver
™
™
MKTG000130 / 202200304_2-1-2013
Solutions Through Advanced Technology™, Qwik™, QwikSEER+ WattSaver™, and QwikProducts™ are trademarks. of
Mainstream Engineering Corporation, 200 Yellow Place, Rockledge, FL 32955
1-800-866-3550 / 321-213-3550
For more product information, please visit
www.Qwik.com/QwikSEER/
or your local distributor
Solutions Through Advanced Technology™
©2012 Mainstream Engineering Corporation
Scan with your
SmartPhone for Info...
U.S. Patents Pending
The
Aordable
Solution
to Enhancing
A/C or
Heat Pump
Systems
MADE IN THE USA
Humidity Removal
Increased Humidity Removal Rate*
82°F
97°F 112°F
% Faster Humidity Removal with QwikSEER+ WattSaver™
Up to
566%
Faster
Humidity
Removal
with
QwikSeer+
WattSaver™
157%
Faster
52%
Faster
Increase Humidity Removal
Rate up to 566%
Indoor air quality (IAQ) is a vital factor in
maintaining a healthy life. By reducing the
humidity in a home, mold growth is avoided.
According to the EPA (http://www.epa.gov/
mold/preventionandcontrol.html), to prevent
mold relative humidity should be maintained
below 60%.
QwikSEER+ WattSaver™ has been shown to
improve humidity removal rates by up to 566%.
This increased moisture removal can significantly
improve indoor comfort while also inhibiting the
formation of mold, thus improving IAQ.
By connecting the optional humidity sensor
(QT6001), the QwikSEER+ control board will also
optimize the system for fastest humidity removal
during high-humidity situations.
Additional Features
of QwikSEER+ WattSaver™
` Added Blower Motor Protection
QwikSEER+ WattSaver’s™ patented design
incorporates high-voltage electrical protection for
voltage spikes.
` 1 Year Limited Warranty
Contact Mainstream Engineering
Corporation for details.
*Based on Independent Laboratory Testing at Intertek (Plano, Texas) of
a 14 SEER system. For complete test results, go to www.qwik.com.
4
SIMPLE INSTALLATION
Disconnect 2 Wires
from Blower Motor
Connect 2 Wires
from Control Board/Relay
to QwikSEER+™ Board
A
Connect 4 Wires
between QwikSEER+™
Board and Blower Motor
B C
Connect 2 Wires
from Control Board/Relay
to QwikSEER+™ Board
1
MOUNT
BRACKET
TO CABINET
A
B
2
THERMISTOR TO A-COIL
FUSE: 250VAC, 20A
TIME DELAY
OUTPUTS TO BLOWER MOTOR
LINE
INPUT
(FROM CONTROL
BOARD OR RELAY)
90-240VAC
50-60Hz
16A MAX
5VDC Side 90-240VAC
Side
COOL
L2
COM
L1
P7
P4 P3 P8
K3
K2
K1
GREEN
to Ground
BLWR LOW
L2 - LOW
BLWR MED
L2 - MED
BLWR HIGH
L2 - HIGH
From Control Board or Relay
Cool Mode (Motor Speed Tap)
From
Control Board
or Relay
Cool Mode
(Common Wire)
BLWR
L1/COM
RED
to Blower
Low Speed Tap
Thermistor
BLUE
to Blower
Med Speed Tap
BLACK
to Blower
High Speed Tap
PURPLE
to Blower
Common
BRACKET SIDE
QT6001
Humidity
Sensor (if equipped)
QwikSEER+ WattSaver™
P/N QT6000
MADE IN THE USA
PATENTS PENDING
CONNECT WIRES
SEE SIMPLIFIED WIRING DIAGRAM
3
ATTACH PCB TO BRACKET
For PSC (Permanent-Split Capacitor) Motors Only
90VAC-240VAC / 1Phase - 16 amp maximum
*Read Complete Instruction Manual Before Installing!
7-13%
*
EER IMPROVEMENT.
7-13%
*EER IMPROVEMENT.