Installation Sheet

1of2
Assembly Instruction Sheet #IS-WNS1610WT
For Style WNS1610WT
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
2017 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2017-07-27
Pleasegoto forproductcleaningtips.Gotothe selection.
IntegratedLED15W
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Package Contents
A
B
Crossbar
x1
Lock Washer
x1
Hex Nut
x1
Nipple
x1
STEP 1 Install the Crossbar to the junction box-
.
A. Attach the Crossbar (A) to the Outlet Box with the head of the Green
Ground Screw facing you. Secure it with Outlet Box Screws (not
included), tighten until snug
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
STEP 2 Install the Nipple
to the Crossbar
-
A. Thread the Hex Nut (C) to
the middle of the Nipple
(D). Place the Lock
Washer (B) over the
Nipple (D) and then thread
the Nipple (D) into the
Crossbar (A) until the
Nipple (D) is about 0.375”
above the Crossbar (A).
B. Place the ceiling canopy
and Fixture Body (F) over
the Nipple (D) against the
ceiling to determine the
correct position of the
Nipple (D). Thread the
Mounting Ball (E) onto the
Nipple (D). Adjust the
Nipple (D) to allow
(Step 2 Continued)
the ceiling canopy and Fixture Body (F) to rest against the ceiling
when held in place by the Mounting Ball (E).
C. Remove the Mounting Ball (E) and the Fixture Body (F). Tighten the
Hex Nut (C) against the Crossbar (A) to secure in place.
Figure 2
C
D
E
Mounting Ball
x1
F
Fixture Body
x1
A
A
B
C
D
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare,orGreen
Ground wire
from outlet box
Ground wire
from fixture
Bare,orGreen
Ground wire
from outlet box
OR
Ground wire
from fixture
Green Ground Screw
on the Crossbar
STEP 4 - Install Fixture Body
A. Place the ceiling canopy and Fixture Body (F) over the end of the
Nipple (D). Secure by threading the Mounting Ball (E) onto the
D
E
E
F
ROTATE
ROTATE
Figure 4
Nipple (D). Hand tighten
until snug.
B. Rotate the lamp to achieve
your desired directions.
Your fixture is now
assembled and ready to
use. Enjoy!
F