Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Victor 4 Light 16" Wide Semi-Flush Drum Ceiling Fixture

1of2

For Style VC1716MB

Pleasegoto forproductcleaningtips.Gotothe selection.

(4)B10CandelabraBaseBulbs60WMaximum,CandelabraBaseT8VintageBulbsarerecommended,bulbsnotincluded.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Crossbar

Assembly

Installation Guide #IS-VC1716MB

2018 QuoizelInc.

ReleasedDate:2018-09-12

visit us on-lineat www.quoizel.com

Lock Ball

x16

Steel Flat Bar

Fixture Body

Center Rod

Socket

Assembly

Ring

Figure 1

STEP 1 Install Steel Flat Bars, Ring-

A. Attach Steel Flat Bars (D) to bolts on the Fixture Body (B) and the

Ring (G). Secure by threading Lock Balls (C) onto bolts. Hand

tighten until snug.

Bolt

STEP 2 - Install Center Rods and

Socket Assembly

A. Thread Center Rod (E) and the

Socket Assembly (F) together.

Hand tighten until snug.

B. Thread the top end of the Center

Rod (E) onto the swivel on the

Fixture Body (B). Hand tighten

until snug.

Swivel

Figure 2

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

STEP 3 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Figure 3

STEP 4 Test Fitting Ceiling Canopy to Crossbar Assembly-

eiling canopy and Fixture Body (B) to the

eiling canopy

Remove mounting balls from the Crossbar Assembly (A). Fit the

c Crossbar Assembly (A)

and secure with mounting balls. Note: The c should be

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Ceiling Canopy

Figure 4

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-VC1716MB For Style VC1716MB Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (4) B10 Candelabra Base Bulbs 60W Maximum, Candelabra Base T8 Vintage Bulbs are recommended, bulbs not included.
PAGE 2
STEP 6 - Install the Fixture (Step 4 Continued) snug against the ceiling and the mounting balls. If not, adjust the length of the nipple on the Crossbar Assembly (A) by unscrewing the preassembled hex nut and lock washer and then screwing the mounting screws in or out of the crossbar until the correct length is achieved. Once the ceiling canopy is secure, remove the mounting ball and Fixture Body (B). A.