Installation Sheet

1of2
For Style TRA1719PK
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
(5)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof
purchase.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Installation Guide #IS-TRA1719PK
2018 QuoizelInc.
visit us on-line at www.quoizel.com
Package Contents
A
Crossbar Assembly
x1
Fixture Body
x1
D
B
C
STEP 2 - Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw facing you. Secure the
Crossbar Assembly (A) with Outlet Box Screws (not included).
Tighten until snug.
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Figure 2
STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
to the
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
Crossbar Assembly (A) and secure with
mounting balls. Note: The should be snug against
the and the mounting balls. If
Fixture Canopy
Fixture Canopy
not, adjust the length of the
nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Fixture Canopy is secure, remove the mounting
ball and Fixture Canopy and proceed to Step 5.
Glass Accent
x1
E
Ring
x1
Bead String
x36
(1pc replacement part)
STEP 4 - Attach the Lanyard
A. The purpose of the lanyard is
to provide a means to support
the fixture hands free from
the junction box while
connecting the electrical
wires.
B.TurntheButtonStopsoit
may be inserted into a
Crossbar slot. Make sure the
Button Stop is completely
inside the Crossbar. Slowly
release the fixture to make
sure it is supported by the
Button Stop. Proceed to the
wiring steps in the next step.
Once you are complete with
the wiring, the Lanyard will
push into the junction box
when the fixture is placed for
final mounting.
Button Stop
Lanyard
Slot
STEP 1 - Installing the Ring
a. Unfold support arms on Fixture Body (B) to proper locations.
b. Remove mounting Screws from the Fixture Body (B). Fit the Ring
(C) to the Fixture Body (B) and secure with mounting balls.
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
Figure 3
Fixture Canopy
ReleasedDate:2018-11-05
C
B
Mounting Screws
Top View
Cap
x1
F