Installation Sheet

1of2
For Style TRA1716PK
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
(4)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof
purchase.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Installation Guide #IS-TRA1716PK
2018 QuoizelInc.
visit us on-line at www.quoizel.com
Package Contents
A
Crossbar Assembly
x1
Fixture Body
x1
D
B
C
STEP 2 - Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw facing you. Secure the
Crossbar Assembly (A) with Outlet Box Screws (not included).
Tighten until snug.
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Figure 2
STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
to the
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
Crossbar Assembly (A) and secure with
mounting balls. Note: The should be snug against
the and the mounting balls. If
Fixture Canopy
Fixture Canopy
not, adjust the length of the
nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Fixture Canopy is secure, remove the mounting
ball and Fixture Canopy and proceed to Step 4.
ReleasedDate:2018-11-05
STEP 1 - Installing the Ring
a. Unfold support arms on Fixture Body (B) to proper locations.
b. Remove mounting Screws from the Fixture Body (B). Fit the Ring
(C) to the Fixture Body (B) and secure with mounting balls.
STEP 4 - Wire Connections
A.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
Figure 4
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Ring
x1
Bead String
x35
(1pc replacement part)
Glass Accent
x1
E
Cap
x1
F
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
Figure 3
Fixture Canopy
C
B
Mounting Screws
Top View