Installation Sheet

1of2
Assembly Instruction Sheet #IS-TMN1616OI
For Style TMN1616OI
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
LED30W
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
ToolsRequired:
LightSource:
EstimatedAssemblyTime:
Preparation:
STEP 3 Install Fixture Body-
A. Align Mounting Screws (B) to keyholes on the Fixture Body (D) and
twist the Fixture Body (D) until the Fixture Body (D) is hung safety.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
B
Outlet Box
Figure 3
(Step 1 Continued)
B. Attach slots on the Crossbar (A) to mounting holes on outlet box
with the head of Green Ground Screw facing you. Secure the
Crossbar (A) with Outlet Box Screws (not included). Tighten until
snug with screwdrivers
C. Test fit the Fixture Body (D) to Mounting Screws (B) and adjust
the length of Mounting Screws (B) so that the Fixture Body (D)
flush against the ceiling after installation. You may need to test fit
more than one time to achieve the correct length of the Mounting
Screw (B).
.
STEP 2 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Figure 2
D
B. By using Phillips screwdrivers,
tighten Mounting Screws (B)
from holes on the lens as
needed to secure the Fixture
Body (D).
Hole
Lens
Package Contents
A
Crossbar
x1
C
Fixture Body
x1
B
Mounting
Screw
x2
D
Shade
x1
Lock Screw
x3
E
Shade Holder
x1
F
STEP 1 Install Crossbar-
A. Measure the distance between two keyholes on the top of the Fixture
Body (D). Use this distance to identify corresponding mounting holes
on the Crossbar (A) and thread Mounting Screws (B) into mounting
holes.
Figure 1
Outlet Box Screws
(not supplied)
A
Outlet Box
Green Ground
Screw
B
D
Keyhole
TOP VIEW OF
CEILING CANOPY
TOP VIEW OF
CEILING
CANOPY
Phillips
Screwdriver
2018 QuoizelInc.
ReleasedDate:2018-03-13
GND