Installation Sheet

Pleasegoto forproductcleaningtips.Gotothe selection.
(2)MediumBaseBulbs75WMaximum,bulbnotincluded,(1)C7CandelabraBaseBulb7WMaximum,bulbincluded.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof
purchase.
www.quoizel.com Care+Maintenance
BulbRecommended:
Estimated Assembly Time:
Preparation:
ToolsRequired:None.
Warnings and Cautions
1of1
Installation Guide #IS-TF4047VB
For Style TF4047VB
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
TF4047VB
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
14.5” Sq.
23.25”
FINISH: VINTAGE BRONZE
2018 QuoizelInc.
ReleasedDate:2018-09-29
visit us on-line at www.quoizel.com
8.25”
Finial
x1
Shade
x1
Bulb (not
included)
Flat Washer
x1
Big Knurled
Nut x 1
Small Knurled
Nut x 1
Base
x1
Cord
Check Ring
x1
Spacer Tube
x1
Nipple with
Hex Nut x 1
A. Insert the Panel into
the Frame and secure the
Panel with Tabs at the
edges of the Frame. (Tab A to
secure big Tiffany panel ,Tab B
to secure the rectangle Tiffany
panel )
B. Thread the hex nut end of the
Nipple with Hex Nut into the
hex coupling on the top center
of the Base. By using the
pliers, thread the hex nut
against the hex coupling and
hand tighten until snug.
C. Place the Spacer Tube and the
Check Ring over the top end of
the Nipple and secure with the
Small Knurled Nut. Hand
tighten until snug.
D. Thread the Big Knurled Nut
onto the top end of the Nipple
and adjust it to proper location
for rest components. Place the
Flat Washer, the Shade, the
Cap and the Rubber Washer
over the top end of the Nipple.
Make Shade is parallel with
Base. Secure with the Finial
and hand tighten until snug.
E. Insert bulbs onto sockets and
screw snugly into place.
Tiffany
Tiffany
Tiffany Panel
x4
Tab
Rubber Washer
x1
Frame
Base
x1
Socket
Assembly
Lock ball
C7 ReplacementBulb
Incorrect
base/ socket/
shade Orientation
Correct
base/ socket/
shade Orientation
Tab A
Tab B
Sides with rough
texture are for
Tiffany outside