Installation Guide
1of1
Assembly Instruction Sheet #IS-TF2801FVB
For Style TF2801FVB
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
2016 QuoizelInc.
A. Thread Socket Assembly, Rod,
Rods with Nipple and Base
together as shown. Hand
tighten until snug. Pull cord
from Base as you assemble
parts together to remove the
excess cord between parts.
B. Thread the Hex Nut end of
Nipple with Hex Nut into hex
coupling on the top center of
Socket Assembly. By using
pliers, thread the Hex Nut
against hex coupling and hand
tighten until snug.
C. Pass Spacer Tube and Check
Ring over the top end of Nipple
with Hex Nut and secure with
Small Knurled Nut.
D. Thread Big Knurled Nut onto
Nipple and adjust it to proper
location for rest components.
Place Flat Washer and Shade
over the top end of Nipple and
secure with Finial. Hand
tighten until snug.
E. This fixture uses standard bulb
with medium base . Maximum
100 watts. Insert bulb and
screw snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
Finial
x1
Bulb (not
included)
TF2801FVB
NOTE:
ALL DIMENSIONS ARE
ROUNDED UP TO THE
NEAREST 1/4"
(2) 100W
Bulbs
(Not Supplied)
Medium
Base
Base
x1
62”
18” Dia.
9.25”
9.75” Dia.
Pleasegoto forproductcleaningtips.Gotothe selection.
(2)MediumBase100WbulbMaximum,Alternatebulb(2)23WCFLMaximum.
15-20minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
Estimated Assembly Time:
Preparation:
Tools Required: None.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
Shade
x1
Flat Washer
x1
Big Knurled
Nut x 1
Small Knurled
Nut x 1
Check Ring
x1
Spacer Tube
4.5”L
x1
Nipple with
Hex Nut 5”L
x1
Socket
Assembly
x1
Rod
x1
Rod with
Nipple
x2
Cord
Hex Coupling
PART NUMBER
G12822SH
REPLACEMENT PART
SHADE
QTY.
1
NO.
1
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2016-06-08
Rod with
Nipple
FINISH: VINTAGE BRONZE
1