Installation Sheet

Pleasegoto forproductcleaningtips.Gotothe selection.
(2)A19MediumBaseBulbs75WMaximum,bulbsnotincluded.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
1of2
Installation Guide #IS-TF1716VB
For Style TF1716VB
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
Package Contents
B
Crossbar
x1
Lock Washer
x1
Hex Nut
x1
Nipple
x1
A
F
Shade
x1
C
D
Lock Ball
x1
E
G
Fixture Body
x1
STEP 1 - Install the Crossbar to the junction box
A. Attach the Crossbar (A) to the outlet box with the head of the green
ground screw facing you. Secure it with outlet box screws (not
included), tighten until snug.
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
A
STEP 2 Install Nipple and Fixture Body-
A. Thread Hex Nut (C) to the middle of the Nipple (D). Place Lock
Washer (B) over the Nipple (D) and then thread the Nipple (D) into
the Crossbar (A) until the Nipple (D) is about 0.375” above the
Crossbar (A).
B. Place the Fixture Body (F) over the Nipple (D) against the ceiling to
determine the correct position of the Nipple (D). Thread the Lock Ball
(E) onto the Nipple (D). Adjust the Nipple (D) to allow the Fixture
Body (F) to rest against the ceiling when held in place by the Lock
Ball (E).
C. Remove the Lock Ball (E) and the Fixture Body (F). Tighten the Hex
Nut (C) against the Crossbar (A) to secure in place.
D. Go to Step 3 for wire connections and follow the directions. Return to
Step E in this step when complete with Step 3.
A
B
C
D
E
(Step 2 Continued)
E. Place the Fixture Body (F) back over the Nipple (D) and secure with
Lock Ball (E). Hand tighten until snug.
Figure 3
Figure 2
F
2018 QuoizelInc.
ReleasedDate:2018-08-07
visit us on-line at www.quoizel.com
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture