User Manual

1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Assembly Instruction Sheet #IS-TB8603C_R1
For Style TB8603C
Pleasegoto forproductcleaningtips.Gotothe selection.
(3)A19MediumBaseBulbs100WMaximum.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Fixture Body
x1
D
Steel Collar
x3
Socket Collar
x3
C
Package Contents
Hardware Contents
AA
BB
CC
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
DD
Mounting Screw
x2
EE
Mounting Ball
x2
Thank you forpurchasing a Quoizelproduct.
Need assistance withparts or assembly?Call Quoizel customerservice at 1-800-645-3184
or visit us on-line at www.quoizel.com
FF
Alternate
Mounting screw
x2
2016 QuoizelInc.
RevisedDate:2016-10-26
B
Finial
x2
E
Glass
Shade
x3
F
Cage
x3
G
Socket
Collar Tool
x1
STEP 1 Install Finials to Fixture Body-
A. Push Finials (B) onto the ends of tubes on the Fixture Body (A)
properly.
Figure 1
A
B
Tube
STEP 2 - Attach Mounting Screws, Lock Washers and Hex Nuts to
Crossbar
A. Line up a set of holes on the Crossbar (AA) and Holes on the
Backplate of Fixture Body (A). Thread Mounting Screws (DD) or
Alternate Short Mounting Screws (FF) into the holes on the
(Step 2 Continued)
Crossbar (AA). Pass Lock Washers (BB) and thread Hex Nuts (CC)
onto the Mounting Screws (DD) or Alternate Short Mounting Screws
(FF). Hand tighten until snug.
Note: Use the Alternate Shorter Mounting Screw (FF) if your
installation requires a shorter mounting screw.
AA
AA
Mounting Screw
or Alternate Short
Mounting Screw
BB
CC
A
Backplate
Figure 2
STEP 3 - Installing the Crossbar Assembly
A. Pass the supply wires through the Crossbar (AA). Attach the
Crossbar (AA) to the Outlet Box with the head of the Green Ground
Screw facing you. Secure the Crossbar Assembly (AA) with Outlet
Box Screws (not included). Tighten until snug.
Outlet Box
Outlet Box Screws
(not included)
AA
Supply Wires
with Ground Wire
Figure 3
STEP 4 - Test Fit the Backplate
to the Crossbar Assembly
A. Place the backplate and Fixture
Body (A) onto the Mounting
Screws (DD) or Alternate Short
Mounting Screws (FF) and
secure with Mounting Balls (EE).
Note: The backplate and Fixture
Body (A) should be snug against
the wall and held tight with the
Mounting Balls (EE). If it is not,
A
Backplate
Hex Nut and
Lock Washer
Mounting Screw
or Alternate Short
Mounting Screw
EE
Figure 4