Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Shrine 3 Light 16" Wide Flush Mount Ceiling Fixture with a Mercury Glass Panel

1of2

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

Assembly Instruction Sheet #IS-SRE1616AGL

For Style SRE1616AGL

Pleasegoto forproductcleaningtips.Gotothe selection.

(3)A19MediumBaseBulbs60WMaximum

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Crossbar Assembly

Thank you forpurchasing a Quoizelproduct.

Need assistance withparts or assembly?Call Quoizel customerservice at 1-800-645-3184

or visit us on-line at www.quoizel.com

Diffuser

2017 QuoizelInc.

ReleasedDate:2017-11-08

Glass Panel

x18

Fixture

Body

Cage

STEP 1 - Install Diffuser and Glass Panels

Install the Glass Panel (E) into the side of the

Cage (C) and secure by folding tabs in the top

and bottom of the Cage (C). Repeat this

process to complete installation of all Glass

Panels (E).

Insert the Diffuser (D) in the bottom of the

Cage (C) and secure by folding tabs in the

bottom edge of the Cage (C).

STEP 2 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

Figure 2

STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-

eiling canopy to the

ceiling

Remove mounting balls from the Crossbar Assembly (A). Fit the

c and Fixture Body (B) Crossbar Assembly (A)

and secure with mounting balls. Note: The should be

snug against the and the mounting balls. If

ceiling canopy

not, adjust the

length of the nipple on the Crossbar Assembly (A) by unscrewing

the preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

achieved. Once the ceiling canopy and Fixture Body (B) is secure,

remove the mounting ball and ceiling canopy and Fixture Body (B)

and proceed to Step 4.

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 3

Tab

Figure 1

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-SRE1616AGL For Style SRE1616AGL 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
PAGE 2
SRE1616AGL STEP 4 - Wire Connections A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. FINISH: AGED GOLD 13.25” Dia.