Installation Sheet

Pleasegoto forproductcleaningtips.Gotothe selection.
(2)A19MediumBaseBulbs60WMaximum,AlternateBulbs(2)13WCFLMaximum.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
1of2
Assembly Instruction Sheet #IS-SNN1612
For Styles SNN1612PN and SNN1612K
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Package Contents
B
Crossbar
x1
Lock Washer
x1
Hex Nut
x1
Nipple
x1
A
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
AA
February2015
F
Socket
Assembly
x1
STEP 2 Install Nipple and Socket Assembly-
* Pliers is required for this step.
A. Thread Hex Nut (C) to the middle of the Nipple (D). Place Lock
Washer (B) over the Nipple (D) and then thread the Nipple (D) into
the Crossbar (A) until the Nipple (D) is about 0.375” above the
Crossbar (A).
C. Place the Socket Assembly (F) over the Nipple (D) against the
ceiling to determine the correct position of the Nipple (D). Thread the
Figure 2
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
C
D
Lock Ball
x1
E
G
Small
Knob
x4
H
Cage
x1
A
B
C
D
F
D
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
STEP 4 - Install Bulbs and Cage
A. Place Diffuser (I) into the Cage (G)
properly.
B. This fixture uses standard bulbs
with standard screw bases.
Maximum 60 watts. Insert bulb and
push snugly into place.
C. Attach the Cage (G) over the Bolts
on the bottom edge of the ceiling
canopy and secure with Small
Knobs (H). Hand tighten until snug.
Your fixture is now assembled and
ready to use. Enjoy!
Socket
Figure 4
G
F
Lock Ball (E) onto the Nipple (D).
Adjust the Nipple (D) to allow the
Socket Assembly (F) to rest against
the ceiling when held in place by the
Lock Ball (E).
D. Remove the Lock Ball (E) and the
Socket Assembly (F). Tighten the Hex
Nut (C) against the Crossbar (A) to
secure in place.
E. Refer to Step 3 for wire connections.
F. Place the Socket Assembly (F) back
over the Nipple (D) and secure with
Lock Ball (E). Hand tighten until snug.
Bolt
G
H
I
Diffuser
x1
I
STEP 5 - Replace
Shade
A
from fixture
. Remove Cage
by
(G)
Small
Knobs (H)
B Unscrew Cup Head
Screws in the Cage
Remove Tab and
Glass Panels from the
Cage.
unlocking
.
.
(G)
C. Reverse above steps
to reinstall the
replacement Glass
Panel onto fixture.
,
Figure 5
Fixture
Body
Cup Head
Screw
Tab
Glass
Panel
Cage
Small
Knob