Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Sector 3 Light 14" Wide Flush Mount Drum Ceiling Fixture

1of2

For Style SCR1614OZ

Pleasegoto forproductcleaningtips.Gotothe selection.

(3)A19MediumBaseBulbs100WMaximum,MediumBaseVintageBulbsarerecommended,bulbsnotincluded.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Crossbar

Assembly

Curve Glass

Flat Glass

Fixture Body

Cage

Installation Guide #IS-SCR1614OZ

2018 QuoizelInc.

ReleasedDate:2018-08-15

visit us on-line at www.quoizel.com

STEP 1 - Install Curve Glasses and Flat Glass

A. Insert the Flat Glass (E) into the bottom of the Cage (D) from the

gap. Secure the Flat Glass (E) by folding the tabs in the bottom of

the Cage.

B. Insert Curve Glasses (B) into the Cage (D). Place the Curve Glasses

(B) onto the slots in the side of the Cage (D).

STEP 2 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Outlet Box

Figure 2

STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-

eiling canopy to the

eiling canopy

ceiling

Remove mounting balls from the Crossbar Assembly (A). Fit the

c and Fixture Body (C) Crossbar Assembly (A)

and secure with mounting balls. Note: The c should be

snug against the and the mounting balls. If not, adjust the

length of the nipple on the Crossbar Assembly (A) by unscrewing the

preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

achieved. Once the ceiling canopy and Fixture Body (C) is secure,

remove the mounting ball and ceiling canopy and Fixture Body (C)

and proceed to Step 4.

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 3

Outlet Box Screws

(not included)

Supply Wires with

Ground Wire

Tab

Slot

Gap

Figure 1

Ceiling

Canopy

Lock Screw

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-SCR1614OZ For Style SCR1614OZ Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (3) A19 Medium Base Bulbs 100W Maximum, Medium Base Vintage Bulbs are recommended, bulbs not included. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation.
PAGE 2
STEP 4 - Wire Connections STEP 7 - Install Cage A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. A.