Installation Sheet

1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Assembly Instruction Sheet #IS-REV1714EK
For Style REV1714EK
Pleasegoto forproductcleaningtips.Gotothe selection.
(4)B10CandelabraBaseBulbs60WMaximumor
(4)T8CandelabraBaseVintage Bulbs are recommended but not supplied.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
A
Crossbar Assembly
x1
D
Thank you forpurchasing a Quoizelproduct.
Need assistance withparts or assembly?Call Quoizel customerservice at 1-800-645-3184
or visit us on-line at www.quoizel.com
Fixture Body
x1
2017 QuoizelInc.
ReleasedDate:2017-03-28
B
Ceiling Canopy
with Nipple
x1
C
Spacer Tube
x1
STEP 1 - Install Ceiling Canopy to Fixture
Body
A. Place the Spacer Tube (C) over the nipple
on the Ceiling Canopy with Nipple (B) and
thread the Ceiling Canopy with Nipple (B)
onto the hex coupling on the top center of
the Fixture Body (D). Hand tighten until
snug.
STEP 2 - Installing the Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Figure 2
Figure 1
D
C
B
STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
eiling canopy and Fixture Body to the
eiling canopy
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
c (D) Crossbar Assembly (A)
and secure with mounting balls. Note: The c should be
snug against the and the mounting balls. If not, adjust the
length of the nipple on the Crossbar Assembly (A) by unscrewing
the preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the ceiling canopy and Fixture Body (D) is secure,
remove the mounting ball and ceiling canopy and Fixture Body (D)
and proceed to Step 4.
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
D
Figure 3
Ceiling
Canopy
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 4
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare,orGreen
Ground wire
from outlet box
Ground wire
from fixture
Bare,orGreen
Ground wire
from outlet box
OR
Ground wire
from fixture
Green Ground Screw
on the Crossbar