Installation Sheet

1of2
2018 QuoizelInc.
Package Contents
A
Ceiling
Canopy
x1
with Nipple
B
Hardware Contents
AA
Crossbar Assembly
x1
Spacer Tube
x1
C
Socket Assembly
x1
Figure 1
STEP 1 Install Ceiling Canopy
with Nipple
-
A. Place the Spacer Tube (B) over
the Hex Coupling on the top
center of the Socket Assembly
(C). Pass the Ceiling Canopy
with Nipple (A) through the
Spacer Tube (B). Thread the
Nipple into the Hex Coupling
and hand tighten until snug.
A
B
C
Figure 2
STEP 2 Install Crossbar Assembly-
.
A. Pass the supply wires through the Crossbar Assembly (AA). Attach
the Crossbar Assembly (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Supply Wires with
Ground Wire
AA
Outlet Box Screws
(not included)
Outlet Box
STEP 3 Fit Ceiling Canopy to
Crossbar Assembly
-
A. Remove mounting balls from the
Crossbar Assembly (AA). Fit the
Ceiling Canopy to the Crossbar
Assembly (AA) and secure with
mounting balls. Note: The Ceiling
Canopy should be snug
Not, adjust the length of
the nipple on the Crossbar
Assembly (AA) by unscrewing the
preassembled hex nut and lock
washer and then screwing the
mounting screws in or out of the
crossbar until the correct length
is achieved. Once the Ceiling
Canopy is secure, remove the
mounting ball and Ceiling
Canopy and proceed to Step 4.
against
the ceiling and the mounting
balls. If
Mounting
Screw
AA
Mounting
Ball
Ceiling
Canopy
Figure 3
Hex Nut and
Lock Washer
2.4mm
13Ga
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
STEP 4 - Wire Connections
A.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
Figure 4
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Assembly Instruction Sheet #IS-RDY1714AWH
For Style RDY1714AWH
Pleasegoto forproductcleaningtips.Gotothe selection.
(3)B10CandelabraBasebulbs60WMaximum.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
ReleasedDate:2018-01-31