Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Dorsey 4 Light 20" Wide Semi-Flush Ceiling Fixture

1of2

For Styles QF5115WT and QF5124WT

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Pleasegoto forproductcleaningtips.Gotothe selection.

(4)A19MediumBase100WbulbMaximum,bulbnotincluded.

MinimumHangingHeightis16.5”,MaximumHangingHeightis52.5”.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

www.quoizel.com Care+Maintenance

LightSource:

FixtureHangingHeight:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Note:This CONVERTIBLEfixturecanbemountedaspendantlightorsemi-flushlight.Refertorespective

installationsteps forinstallations.

Installation Guide

2019 QuoizelInc.

ReleasedDate:2019-04-04

visit us on-line at www.quoizel.com

Fixture Body

Package Contents

Crossbar Assembly

Ceiling Canopy

6” Rod

12” Rod

Swivel

Allen Wrench

Assembly Instructions for Pendant Light: QF5115WT

(Step 1A - Step 6A)

STEP 1A - Install Ceiling Canopy, Rods

and Fixture Body together

A. Thread the Swivel (E) onto the Ceiling

Canopy (D), Hand tighten until snug.

Tighten the set screw on the swivel (E)

by using the Allen Wrench (G).

B. Determine the Rods (B/C) to be

assembled to the Fixture Body (F)

according to your hanging height.

C. Pass the supply wires and ground wire

through the chosen rods (B/C) and the

Ceiling Canopy (D). Thread the Fixture

Supply

Wires and

Ground Wire

Set Screw

Body (F), the chosen

Rods (B/C) and the

Ceiling Canopy (D)

together. Hand tighten

until snug.

Suggested rods for

Ceiling height :

8’ ceiling : use (1) 6”

rods and (1) 12” rods

9’ ceiling : use (1) 6”

rods and (2) 12” rods

Figure 1A

STEP 2A - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

Figure 2A

STEP 3A Test Fitting Ceiling Canopy to Crossbar Assembly-

to the

ceiling

Remove mounting balls from the Crossbar Assembly (A). Fit the

Crossbar Assembly (A) and secure with

mounting balls. Note: The should be snug against

the and the mounting balls. If

Fixture Canopy

not, adjust the length of the

nipple on the Crossbar Assembly (A) by unscrewing the

preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

achieved. Once the Fixture Canopy is secure, remove the mounting

ball and Fixture Canopy and proceed to Step 4A.

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Fixture Canopy

Figure 3A

Summary of content (2 pages)

PAGE 1
Installation Guide For Styles QF5115WT and QF5124WT Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (4) A19 Medium Base 100W bulb Maximum, bulb not included. Fixture Hanging Height: Minimum Hanging Height is 16.5”, Maximum Hanging Height is 52.5”.
PAGE 2
Assembly Instructions for Semi-Flush Light: QF5124WT (Step 1B) STEP 4A - Wire Connections A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.