Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Pritchett 4 Light 18" Wide Flush Mount Ceiling Fixture

1of2

For Style QF4059K

Package Contents

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Crossbar

Assembly

Pleasegoto forproductcleaningtips.Gotothe selection.

(4)B10CandelabraBasebulbs60WMaximum,CandelabraBaseT8Vintage Bulbs are recommended, bulbs not included..

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Installation Guide #IS-QF4059K

Fixture Body

Lock Screw

2018 QuoizelInc.

ReleasedDate:2018-10-18

visit us on-line at www.quoizel.com

Cage

Triangle

Glass Panel

Rectangle

Glass Panel

Square

Glass

Panel

STEP 1 - Install the Square Glass Panel

A. Place the Square Glass Panel (E) into the bottom of the Cage (G)

and secure by folding tabs in the bottom edge.

Tab

Figure 1

STEP 2 - Install Triangle Glass Panels and Rectangle Glass

Panels

A. Place Triangle Glass Panels (C) and Rectangle Glass Panels (D)

into the side of the Cage (G) and secure by folding tabs in the edge.

Tab

Figure 2

STEP 3 - Install the Crossbar Assembly to Outlet Box and Adjust

the length of the Nipple

A. Attach the Crossbar Assembly (A) to the Outlet Box with the head of

the Green Ground Screw facing you. Secure it with Outlet Box

Screws (not included), tighten until snug

B. Adjust the hex nut and lock washer underside of the crossbar to the

middle of the nipple.

C. Remove the mounting ball from the nipple. Place the Fixture Body

(F) over the nipple against the ceiling to determine the correct

position of the nipple. Thread the mounting ball onto the nipple.

Adjust the nipple to allow the Fixture Body (F) to rest against the

ceiling when held in place by the mounting ball.

D. Remove the mounting ball and the Fixture Body (F). Tighten the

lock washer and the hex nut against the crossbar to secure in place.

Hex Nut and

Lock Washer

Nipple

Green Ground Screw

Outlet Box Screw

(not included)

Mounting Ball

Figure 3

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-QF4059K For Style QF4059K Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (4) B10 Candelabra Base bulbs 60W Maximum, Candelabra Base T8 Vintage Bulbs are recommended, bulbs not included..
PAGE 2
STEP 4 - Wire Connections QF4059K A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.