Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Piermont 2 Light 14" Wide Semi-Flush Ceiling Fixture with a Glass Shade

1of2

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

Assembly Instruction Sheet #IS-PMT1714EK

For Style PMT1714EK

Pleasegoto forproductcleaningtips.Gotothe selection.

(2)A19MediumBaseBulbs100WMaximumor

(2)MediumBaseVintageBulbsarerecommendedbutnotsupplied.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Thank you forpurchasing a Quoizelproduct.

Need assistance withparts or assembly?Call Quoizel customerservice at 1-800-645-3184

or visit us on-line at www.quoizel.com

2017 QuoizelInc.

ReleasedDate:2017-09-28

Package Contents

Crossbar Assembly

Lock Screw

Fixture

Body

Glass

Shade

STEP 1 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Figure 1

Outlet Box Screws

(not included)

Supply Wires with

Ground Wire

Outlet Box

STEP 2 Test Fitting Ceiling Canopy to Crossbar Assembly-

eiling canopy to the

ceiling

Remove mounting balls from the Crossbar Assembly (A). Fit the

c and Fixture Body (C) Crossbar Assembly (A)

and secure with mounting balls. Note: The should be

snug against the and the mounting balls. If

ceiling canopy

not, adjust the

length of the nipple on the Crossbar Assembly (A) by unscrewing

the preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

(Step 2 Continued)

achieved. Once the ceiling canopy and Fixture Body (C) is secure,

remove the mounting ball and ceiling canopy and Fixture Body (C)

and proceed to Step 3.

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Ceiling Canopy

Figure 2

STEP 3 - Wire Connections

A. Wrap bare or green ground wire around green ground screw on the

crossbar, no less than 2 inches from the end of the wire. Tighten the

green ground screw.

B. Use standard wire connectors (not included) to make all wire

connections. Twist connectors until wires are tightly joined together.

Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

Figure 3

Green Ground Screw

on the Crossbar

White wire

from outlet box

White wire

from fixture

Black wire from

outlet box (or Red)

Black wire

from fixture

Bare, or Green

Ground wire

from outlet box

Ground wire

from Fixture

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-PMT1714EK For Style PMT1714EK 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (2) A19 Medium Base Bulbs 100W Maximum or (2) Medium Base Vintage Bulbs are recommended but not supplied.
PAGE 2
STEP 4 - Install the Fixture STEP 5 - Install Bulbs and Glass Shade A. Carefully tuck all wires into the outlet box and position the ceiling canopy and Fixture Body (C) over the outlet box. Align the holes in the ceiling canopy with the mounting screws, then attach the ceiling canopy and Fixture Body (C) using the previously removed mounting balls. Hand tighten until snug. A. Insert bulbs onto sockets and screw snugly into place. B. Attach the Glass Shade (D) to the ring.