Installation Sheet

Pleasegoto forproductcleaningtips.Gotothe selection.
(5)ClearG9XenonBulbs40WMaximum(supplied)
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
1of3
Assembly Instruction Sheet #IS-PCVE1616C
For Style PCVE1616C
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Do not touch the bulb with bare hands use a cloth or glove.
Package Contents
A
Inner Backplate
x1
E
Fixture Body
x1
Clear G9
Xenon Bulb
x5
F
Crystal B
(1) Bead w/ (1) Drop
x10
Crystal A
(3) Beads w/ (1) Drop
x5
Crystal C
Crystal Tube
x28
STEP 2 - Test Fit the Fixture Body to the Inner Backplate
A. Remove the mounting balls from the Inner Backplate (A). Place the
cross-cut on the insulation inside of the ceiling canopy and the
Fixture Body (E) over mounting screws on the Inner Backplate (A).
Place the Fixture Body (E) onto the Inner Backplate (A) and secure
with mounting balls. Note: The Fixture Body (E) should be snug
against the ceiling and held tight with the mounting balls. If it is not,
adjust the length of the mounting screws on the Inner Backplate (A)
by unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws in or out of the Inner Backplate (A)
until the correct length is achieved. Once the Fixture Body (E) is
secure, remove the mounting ball and Fixture Body (E) and proceed
to Step 3.
Mounting Ball
E
Mounting Screw
Hex Nut and
Lock Washer
Figure 2
2017 QuoizelInc.
ReleasedDate:2017-08-31
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
G
N
D
C
Wall Anchor
x4
D
Self-tapping
Screw
x4
Washer
x4
B
STEP 1 Install Inner Backplate-
A. Attach the Inner Backplate (A) onto the Outlet Box and make four
marks on the ceiling from keyholes on the Inner Backplate (A).
Figure 1
Outlet Box
A
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
B
Keyhole
D
C
(Step 1 Continued)
B. Remove the Inner Backplate (A) and drill proper holes on the ceiling
from marks. Insert Wall Anchors (B) into the holes properly. Pass
supply wires and ground wire through the center hole of the Inner
Backplate (A). Attach the Inner Backplate (A) to Outlet Box. Thread
Outlet Box Screws (not Supplied) into mounting holes on the Outlet
Box. Pass Washers (D) over Self-tapping Screws (C) and thread
Self-tapping Screws (C) into Wall Anchors (B). Hand tighten until
snug.
G
Crystal
Insulation Inside
of Ceiling Canopy
Cross-cut
Ceiling Canopy