Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Clear Hollow 5 Light 10-3/4" Wide Integrated LED Flush Mount Square Ceiling Fixture with Pressed Crystal Shades

Package Contents

Pleasegoto forproductcleaningtips.Gotothe selection.

Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses,markingpen,1/4”

drillbitanddrill.

LED19W

MissingParts?Contactyouroriginalplaceof

purchase.

www.quoizel.com Care+Maintenance

ToolsRequired:

LightSource:

EstimatedAssemblyTime:

Preparation:

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.

Warnings and Cautions

1of2

For Style PCHL1611C

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Crossbar

Assembly

Mounting Screw

Fixture Body

Crystal

2.4mm

13 Ga13 Ga

Installation Guide PCHL1611C#IS-

2018 QuoizelInc.

ReleasedDate:2018-04-13

visit us on-line at www.quoizel.com

Wall Anchor

Screw

Washer

STEP 1 Install Crystals-

A. Remove lock screws from sockets.

B. Attach Crystals (F) onto sockets and secure with previously removed

lock screws. Hand tighten until snug with screwdrivers gently.

Figure 1

Lock Screw

Socket

Figure 2

Outlet Box

Outlet Box Screw

(not included)

Supply Wires with

Ground Wire

STEP 2 Attach Crossbar Assembly to Outlet Box-

A. Attach the Crossbar Assembly (A) onto the outlet box and make two

marks on the ceiling from keyholes.

B. Remove the Crossbar Assembly (A). Using a 1/4” drill bit, drill holes

at each (2) locations marked on the ceiling.

C. Insert Wall Anchors (C) into drilled holes completely.

D. Pass supply wires and ground wire through the center hole of the

Crossbar Assembly (A). Attach the Crossbar Assembly (A) to outlet

box. Thread outlet box screws (not included) into mounting holes on

the outlet box. Pass Washers (E) over Screws (D) and thread

Screws (D) into Wall Anchors (C). Hand tighten until snug with

screwdrivers.

STEP 3 - Wire Connections

A. Wrap bare or green ground wire around green ground screw on the

crossbar, no less than 2 inches from the end of the wire. Tighten the

green ground screw.

B. Use standard wire connectors (not included) to make all wire

connections. Twist connectors until wires are tightly joined together.

Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

Figure 3

Green Ground Screw

on the Crossbar

White wire

from outlet box

White wire

from fixture

Black wire from

outlet box (or Red)

Black wire

from fixture

Bare,orGreen

Ground wire

from outlet box

Ground wire

from Fixture

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-PCHL1611C For Style PCHL1611C Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses, marking pen, 1/4” drill bit and drill. Light Source: LED 19W Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation.
PAGE 2
STEP 4 - Attach Fixture Body to Crossbar A. F it excess cord and electrical wires in the ceiling canopy properly. Line up the holes on the side of the c eiling c anopy to the mounting holes on the Crossbar Assembly (A). Secure them with Mounting Screws (B). Tighten until sung. A B Ceiling Canopy Your fixture is now assembled and ready to use. Enjoy! Figure 4 PCHL1611C NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" FINISH: POLISHED CHROME 9” SQ. 2.4mm 13 Ga G ND 4.25” 2” 2” 2” 10.