Installation Sheet

Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
(5)G9BaseClearG9XenonBulbs40WMaximum(supplied).
www.quoizel.com Care+Maintenance
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
LightSource:
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-PCGN1616C
For Style PCGN1616C
2017 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Do not touch the bulb with bare hands use a cloth or glove.
B
Fixture Body
x1
Crossbar Assembly
x1
A
C
Clear G9
Xenon Bulb
x5
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2017-04-01
D
Crystal Strings
Crystal
String B
x8
Crystal
String C
x24
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires with ground wire through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to Outlet Box with
the head of Green Ground Screw facing you. Secure it with Outlet
Box Screws (not included). Tighten until snug.
STEP 2 - Test Fit the Ceiling Canopy to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the ceiling canopy and the Fixture Body (B) onto the Crossbar
Assembly (A) and secure with mounting balls. Note: The ceiling
canopy and the Fixture Body (B) should be snug against the ceiling
and held tight with the mounting balls. If it is not, adjust the length of
the mounting screws on the Crossbar Assembly (A) by unscrewing
Crystal
String A
x3
(Step 2 Continued)
the preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Fixture Body (B) is secure, remove the
mounting ball and Fixture Body (B) and proceed to Step 3.
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
Bare, or Green
Ground wire
from outlet box
OR
Ground wire
from fixture
Green Ground Screw
on the Crossbar
Figure 3
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Figure 1
Mounting
Screw
Hex Nut and
Lock Washer
Mounting
Ball
A
B
Figure 2
Ceiling
Canopy