Installation Sheet

1of2
For Style PCEO1618C
Installation Guide IS-PCEO1618C#
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
LED21W
Contactyouroriginalplaceofpurchase.
www.quoizel.com Care+Maintenance
ToolsRequired:
LightSource:
EstimatedAssemblyTime:
Preparation:
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Supply Wires with
Ground Wire
2018 QuoizelInc.
ReleasedDate:2018-08-10
visit us on-line at www.quoizel.com
Package Contents
B
Inner Backplate
x1
A
Mounting Screw
x3
Fixture Body
x1
STEP 1 Attach Inner Backplate to Outlet Box-
A. Attach the Inner Backplate (A) onto the outlet box and make three
marks on the ceiling from holes.
B. Remove the Inner Backplate (A). Using a 1/4” drill bit, drill holes at
each (3) locations marked on the ceiling.
C. Insert Wall Anchors (C) into drilled holes completely.
D. Pass supply wires and ground wire through the center hole of the
Inner Backplate (A). Attach the Inner Backplate (A) to outlet box.
Thread outlet box screws (not included) into mounting holes on the
outlet box. Pass Washers (E) over Screws (D) and thread Screws
(D) into Wall Anchors (C). Hand tighten until snug with
screwdrivers.
F
Crystal [1pc
Replacement
Crystal included]
x40
Outlet Box
A
Outlet Box Screw
(not included)
STEP 2 - Attach the Lanyard
A. The purpose of the lanyard is to provide a means to support the
fixture hands free from the junction box while connecting the
electrical wires.
B. Turn the Button Stop so it may be inserted into a inner backplate
slot. Make sure the Button Stop is completely inside the inner
backplate. Slowly release the fixture to make sure it is supported by
the Button Stop. Proceed to the wiring steps in the next step. Once
you are complete with the wiring, the Lanyard will push into the
junction box when the fixture is placed for final mounting.
Button Stop
Lanyard
Slot
A
Figure 2
GN
D
E
C
Wall Anchor
x3
D
Screw
x3
Washer
x3
C
D
E
Figure 1
Hole
Figure 3
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
G
Remove to install
crystals and reinstall
when finish
Remove to install
crystals and reinstall
when finish
G