Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Embrace Single Light 13-3/4" Wide Integrated LED Flush Mount Square Ceiling Fixture with Crystal Accents

Package Contents

Pleasegoto forproductcleaningtips.Gotothe selection.

Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

LED25W

www.quoizel.com Care+Maintenance

ToolsRequired:

LightSource:

EstimatedAssemblyTime:

Preparation:

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

Warnings and Cautions

1of2

Assembly Instruction Sheet #IS-PCEM1614C

For Style PCEM1614C

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

2018 QuoizelInc.

ReleasedDate:2018-03-13

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184

or visit us on-line at www.quoizel.com

Fixture Body

Inner Backplate

Mounting Screw

Wall Anchor

Washer

Self-tapping Screw

Crystal (1pc

Replacement

Included)

x57

STEP 3 Install Crystal

Holders to Fixture Body

A. Attach big crystal holders

with Crystals (G) to Fixture

Body (F) first. Align holes on

the corners of the big crystal

holder to couplings and

secure with previously

removed screws. Hand

tighten until snug with

screwdrivers.

C. Use the same process to

install small crystal holder

with Crystals (G) to the

Fixture Body (F).

Figure 2

Screw

Coupling

STEP 4 Attach Inner Backplate to Outlet Box-

A. Attach the Inner Backplate (A) onto the outlet box. Align one set of

holes on the Inner Backplate (A) to mounting holes on the outlet box

and make two marks on the ceiling from keyholes on the flat strap of

the Inner Backplate (A).

B. Remove the Inner Backplate (A) and drill proper holes on the ceiling

from marks. Insert Wall Anchors (C) into the holes properly.

C. Attach the Inner Backplate (A) to outlet box. Secure by threading

outlet box screws (not supplied) into mounting holes on the outlet

box and threading Self-tapping Screws (E) with Washers (D) into

Wall Anchors (C). Hand tighten until snug.

Supply Wires and

Ground Wire

Outlet

Box

Outlet Box Screw

(not supplied)

Figure 4

STEP 1 Remove Crystal Holders-

A. Unscrew screws and remove

crystal holders from the Fixture

Body (F).

Screw

Small Crystal Holder

Big Crystal Holder

Figure 1

STEP 2 Install Crystals-

A. Attach Crystals (G) to pins on big/small crystal holders and then

bend pins to hold Crystals (G) in safety.

Crystal Holder

Small Crystal

Holder

Big Crystal

Holder

Figure 3

Push

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-PCEM1614C For Style PCEM1614C Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: LED 25W Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present.
PAGE 2
STEP 5 - Wire Connections STEP 6 - Attach Fixture Body to Inner Backplate A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. A.