Installation Sheet

Package Contents
1of2
For Style PCBK1614C
Pleasegoto forproductcleaningtips.Gotothe selection.
markingpen,1/4”
drillbitanddrill.
IntegratedLED20W.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses,
STEP 1 - Attach Inner Backplate to Outlet Box
A. Attach the Inner Backplate (A) onto the outlet box and make four
marks on the ceiling from a set of slot holes.
Installation Guide #IS-PCBK1614C
2019 QuoizelInc.
ReleasedDate:2019-01-22
visit us on-line at www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
G
N
D
A
Inner Backplate
x1
Mounting Screw
x4
B
Rubber Washer
x4
H
Fixture Body
x1
F
Lock Screw
x4
I
Diffuser
x1
G
C
Wall Anchor
x4
D
Screw
x4
Washer
x4
E
Outlet Box
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
A
C
D
E
Figure 1
Slot Hole
(Step 1 Continued)
B. Remove the Inner Backplate (A). Using a 1/4” drill bit, drill holes at
each (4) locations marked on the ceiling.
C. Insert Wall Anchors (C) into drilled holes completely.
D. Pass supply wires and ground wire through the center hole of the
Inner Backplate (A). Attach the Inner Backplate (A) to outlet box.
Thread outlet box screws (not included) into mounting holes on the
outlet box. Pass Washers (E) over Screws (D) and thread Screws (D)
into Wall Anchors (C). Hand tighten until snug with screwdrivers.
STEP 2 - Attach Lanyards
A. The purpose of the lanyard is to provide a means to support the
fixture hands free from the junction box while connecting the
electrical wires.
B. Turn the Button Stop so it may be inserted into a Inner Backplate slot.
Make sure the Button Stop is completely inside the Inner Backplate.
Slowly release the fixture to make sure it is supported by the Button
Figure 2
Lanyard
Button Stop
A
F
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Stop. Proceed to the
wiring steps in the
next step. Once you
are complete with the
wiring, the Lanyard
will push into the
junction box when the
fixture is placed for
final mounting.