Installation Sheet

1of2
For Styles WT, NHR1720WT, and NHR1720BNNHR2820 NHR2820BN
Pleasegoto forproductcleaningtips.Gotothe selection.
(5)A19MediumBaseVintageBulbs100WMaximum,bulbsincluded.
MinimumHangingHeightis11.75”,MaximumHangingHeightis49.75”.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care+Maintenance
LightSource:
FixtureHangingHeight:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Note:This CONVERTIBLEfixturecanbemountedaspendantlightorsemi-flushlight.Refertorespective
installationsteps forinstallations.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Installation Guide
2019 QuoizelInc.
ReleasedDate:2019-04-04
visit us on-line at www.quoizel.com
Package Contents
A
Crossbar
Assembly
x1
B
6” Rod
x2
C
12” Rod
x2
H
Fixture Body
x1
E
Ceiling Canopy
x1
F
Nipple
Assembly
x1
D
Vintage Bulb
x5
G
Spacer Tube
x1
Assembly Instructions for Pendant Light:
NHR2820WT and NHR2820BN
(Step 1A - Step 7A)
F
G
H
STEP 1A - Install Nipple and Spacer Tube
A. Place the Spacer Tube (G) over the hex coupling on the top center of
the Fixture Body (H). Thread the Nipple Assembly (F) onto the hex
coupling on the Fixture Body (H) and hand tighten until snug to
secure the Spacer Tube (G).
Figure 1A
STEP 2A - Install Ceiling Canopy, Rods and Nipple together
A. Tighten the hex nut inside of the Ceiling Canopy (E).
B. Determine the Rods (B/C) to be assembled to the Nipple (F)
according to your hanging height.
C. Pass the supply wires and ground wire through the chosen rods
(B/C) and the Ceiling Canopy (E). Thread the Nipple (F), the chosen
Rods (B/C) and the Ceiling Canopy (E) together. Hand tighten until
snug.
E
B
C
F
Supply Wires
and Ground Wire
C
B
Figure 2A
STEP 3A - Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the outlet box
with the head of the green ground screw facing you. Secure the
Crossbar Assembly (A) with outlet box screws (not included).
Tighten until snug.
Outlet Box Screws
(not included)
A
Outlet Box
Supply Wires with
Ground Wire
Figure 3A
Hex Nut
Suggested rods for Ceiling
height :
8’ ceiling : use (2) 12” rods
9’ ceiling : use (2) 6” rods and
(2) 12” rods