Installation Guide

Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A21MediumBasebulb150WMaximum,Alternatebulb(1)42WCFL.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-MLS1907IB
For Style MLS1907IB
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Hardware Contents
AA
BB
CC
DD
EE
FF
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
Nipple
x1
Canopy
Chain Loop
x1
Canopy Lock
Ring
x1
Ceiling
Canopy
x1
HH
Quick Link
x2
A
Band
Iron
x1
September2015
II
GG
Fixture Chain
x1
Figure 2
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
AA
STEP 2 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
STEP 3 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end of
the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Step
B
Step
A
CC
BB
EE
II
FF
AA
BB
CC
DD
Figure 3
Canopy Chain Loop (EE) and hand
tighten until snug.
B. Thread another Hex Nut (CC) to the
middle of the Nipple (DD). Place
another Lock Washer (BB) over the
Nipple (DD) and then thread the
Nipple (DD) into the Crossbar (AA)
until the Nipple (DD) is about 0.375”
above the Crossbar (AA).
C. Remove the Canopy Lock Ring (FF)
from the Canopy Chain Loop (EE).
Place the Ceiling Canopy (II) over the
Canopy Chain Loop (EE) against the
ceiling to determine the correct
position of the Nipple (DD). Thread
the Canopy Lock Ring onto the
Canopy Chain Loop (EE). Adjust the
Nipple (DD) to allow the Ceiling
Canopy (II) to rest against the ceiling
when held in place by the Canopy
Lock Ring (FF).
D. Remove the Canopy Lock Ring (FF)
and the Ceiling Canopy (II). Tighten
the Hex Nut (CC) against the
Crossbar (AA) to secure in place.
B
Fixture
Body
x1
C
Lock Nut
x2
D
Glass
Panel
x4
E
Glass
Holder
x4
F
Lock
Screw
x8
STEP 1 Install Glass Panel
andBandIronontoFixture
Body
-
A. Line up the Hole on the Band
Iron (A) and the Mounting
Hole on the Fixture Body (B),
secure by threading Lock Nut
(C) into the Mounting Hole.
Hand tighten until sung.
B. Insert Glass Panel (D) into the
Slot in the Fixture Body (B).
Line up the hole on the Glass
Holder (E) and the mounting
hole on the Fixture Body (B),
secure by threading Lock
Screw (F) into the Mounting
Hole, hand tighten until sung.
A
C
B
F E
D
Mounting
Hole
Hole
Slot
STEP 4 - Install Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (GG) to your desired length by removing
links if needed.
Pliers is required for this step.
B. With the Fixture Chain (GG) not attached to the Fixture Loop and the
Canopy Chain Loop (EE), pull the supply wires through the Fixture
*