Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Middleton 3 Light 12" Wide Semi-Flush Ceiling Fixture with a Glass Shade

1of2

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

Assembly Instruction Sheet #IS-MID1712BN

For Style MID1712BN

Pleasegoto forproductcleaningtips.Gotothe selection.

(3)B10CandelabraBaseBulbs60WMaximum

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Crossbar Assembly

Thank you forpurchasing a Quoizelproduct.

Need assistance withparts or assembly?Call Quoizel customerservice at 1-800-645-3184

or visit us on-line at www.quoizel.com

Fixture

Body

2017 QuoizelInc.

ReleasedDate:2017-08-14

STEP 1 - Install Shade and Cap to

Fixture Body

A. Thread the Nipple with Hex Nut (C)

into the coupling underside of the

Fixture Body (B). By using pliers,

thread the hex nut against the

coupling and hand tighten until

snug.

B. Insert bulbs onto sockets and

screw snugly into place.

C. Place the Shade (D), the Rubber

Washer (F) and the Flat Washer (E)

over the end of the Nipple (C) as

shown. Secure by threading the

Hex Nut (G) onto the Nipple (C).

Hand tighten until snug.

D. Place the Cap (H) over the enc of

the Nipple (C) and secure with the

Finial (I). Hand tighten until snug.

Nipple with

Hex Nut

Flat Washer

Rubber Washer

Shade

Cap

Finial

Hex Nut

Bulb (not

supplied)

Socket

Coupling

Figure 1

STEP 2 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

Figure 2

STEP 3 Test Fitting Ceiling

Canopy to Crossbar Assembly

eiling canopy

to the

ceiling

Remove mounting balls from

the Crossbar Assembly (A).

Fit the c and

Fixture Body (B)

Crossbar Assembly (A) and

secure with mounting balls.

Note: The

should be snug against the

and the mounting

balls. If

ceiling canopy

not, adjust the length

of the nipple on the Crossbar

Assembly (A) by unscrewing

the preassembled hex nut

and lock washer and then

Mounting

Screw

Hex Nut and

Lock Washer

Mounting

Ball

Ceiling

Canopy

Figure 3

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-MID1712BN For Style MID1712BN 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
PAGE 2
(Step 3 Continued) STEP 5 - Install the Fixture screwing the mounting screws in or out of the crossbar until the correct length is achieved. Once the ceiling canopy and Fixture Body (B) is secure, remove the mounting ball and ceiling canopy and Fixture Body (B) and proceed to Step 4. A. Carefully tuck all wires into the outlet box and position the ceiling canopy and Fixture Body (B) over the outlet box.