Installation Sheet

1of2
Assembly Instruction Sheet #IS-LWN1716BN
For Style LWN1716BN
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
2018 QuoizelInc.
ReleasedDate:2018-09-03
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Pleasegoto forproductcleaningtips.Gotothe selection.
(3)A19MediumBaseBulbs100WMaximum,MediumBaseVintageBulbsarerecommended,bulbsnotincluded.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Fixture Body
x1
B
C
Shade
x3
A
Crossbar
x1
Assembly
STEP 1 - Install the Crossbar Assembly to Outlet Box and Adjust
the length of the Nipple
A. Attach the Crossbar Assembly (A) to the Outlet Box with the head of
the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included), tighten until snug
B. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
C. Remove the and Hex Nut from the Nipple. Place the
Ceiling Canopy over the Nipple against the ceiling to determine the
correct position of the nipple. Thread the Finial onto the Nipple.
Adjust the nipple to allow the Ceiling Canopy to rest against the
ceiling when held in place by the .
D. Remove the and the Fixture Body (B). Tighten the lock
washer and the hex nut against the crossbar to secure in place.
.
Lock Ball
Lock Ball
Lock Ball
Outlet Box Screw
(not included)
Hex Nut and
Lock Washer
Outlet Box
Green Ground Screw
A
Lock Ball
Figure 1
Nipple
Hex Nut
Ceiling Canopy
STEP 2 - Wire Connections
A.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
Figure 2
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Outlet Box
Figure 3
Nipple
Hex Nut
B
Lock Ball
STEP 3 - Install the Fixture Body
A. Attach the Fixture Body (B) over the end of the Nipple and secure
with the Hex Nut. Hand tighten until snug.
B. Thread the Lock Ball onto the Nipple and hand tighten until snug.
Lock Screws
()
x9
Pre-assembled to Fixture Body
E