Installation Guide

ManualsBrandsQuoizel ManualsKitchen Island LightingDWL540WT

Pleasegoto forproductcleaningtips.Gotothe selection.

(5)CandelabraBaseBulbs60WMaximum

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

1of2

Assembly Instruction Sheet #IS-DWL540WT

For Style DWL540WT

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

2016 QuoizelInc.

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Hardware Contents

Crossbar

Lock

Washer

Hex Nut

Nipple

Quick

Link

Ceiling

Canopy

Lock

Ball

Figure 1

STEP 1 Assemble the Fixture Loop, Cage, Rod and Socket

Assembly

A. Thread Rods(A) onto the Socket Assembly (C), hand tighten until

sung.

B. Pass the Rods through the Cage (D) and Rubber Washer (E), secure

by threading Fixture Loop (A) onto the Rods(B). Hand tighten until

sung.

Fixture Chain

Fixture

Loop

Cage

Rod

STEP 2 Install Crossbar-

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the Green

Ground Screw facing you. Secure it with Outlet Box Screws (not

included) Tighten until snug..

Figure 2

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

STEP 3 Install Nipple to Crossbar-

* Pliers is required for this step.

A. Thread the Hex Nut (CC) to the middle of the Nipple (DD). Place the

Lock Washer (BB) over the Nipple (DD) and then thread the Nipple

(DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375”

above the Crossbar (AA).

Step A

Figure 3

B. Place the Ceiling Canopy (HH)

over the Nipple (DD) against the

ceiling to determine the correct

position of the Nipple (DD). Thread

the Lock Ball (EE) onto the Nipple

(DD). Adjust the Nipple (DD) to

allow the Ceiling Canopy (HH) to

rest against the ceiling when held

in place by the Lock Ball (EE).

C. Remove the Ceiling Canopy (HH)

and then tighten the Hex Nut (CC)

against the Crossbar (AA) to

secure in place.

Figure 4

STEP 4 Assemble

Ceiling Canopy, Fixture

Chain, Fixture Body

together

A. Pass Supply Wires

and Ground Wire

through the Quick Link

(FF) and the Ceiling

Canopy (HH). Attach

one end of Fixture

Chain (GG) to the

Ceiling Canopy (HH)

by using Quick Link

(FF), attach the other

end of Fixture Chain

(GG) to the Fixture

Loop (A) by using

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-DWL540WT For Style DWL540WT 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
PAGE 2
STEP 5 - Wire Connections A. Use standard wire connectors (not included) to make all wire connections. (Connectors are not included with fixture.) Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into outlet box. Note: If the electrical wire is going to be cut shorter than provided you will need to identify the "L" line wire and the "N" neutral wire before you cut the excess wire off.