Installation Guide

Pleasegoto forproductcleaningtips.Gotothe selection.
(1)MediumBase150WbulbMaximumor
(1)MediumBaseVintageBulbisrecommendedbutnotsupplied.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-CSE1910
For Styles CSE1910PN and CSE1910EK
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
H
Shade
x1
I
Steel
Collar
x1
J
Socket
Collar
x1
Package Contents
Crossbar
Assembly
x1
Ceiling Canopy
x1
Fixture Chain
x1
Quick Link
x2
A
Fixture Body
x1
B
C
D
E
Outlet Box Screw
x2
F
Wire Connector
x3
G
STEP 1 - Install the Crossbar Assembly to Outlet Box and Adjust
the length of the Nipple
A. Attach the Crossbar Assembly (A) to the Outlet Box with the head of
the Green Ground Screw facing you. Secure it with Outlet Box
Screws (F), tighten until snug
B. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
C. Remove the canopy lock ring from the canopy chain loop. Place the
Ceiling Canopy (D) over the canopy chain loop against the ceiling to
determine the correct position of the nipple. Thread the canopy lock
ring onto the canopy chain loop. Adjust the nipple to allow the Ceiling
Canopy (D) to rest against the ceiling when held in place by the
canopy lock ring.
D. Remove the canopy lock ring and the Ceiling Canopy (D). Tighten
the lock washer and the hex nut against the crossbar to secure in
place.
.
Hex Nut and
Lock Washer
Outlet Box
Green Ground Screw
Canopy Chain Loop
Canopy Lock Ring
Nipple
Figure 1
D
A
F
2018 QuoizelInc.
ReleasedDate:2018-11-12
visit us on-line at www.quoizel.com
Nipple
Fixture
Loop
Supply
Wires and
Ground Wire
Canopy
Chain Loop
Canopy
Lock Ring
C
B
D
C
Figure 3
STEP 2 - Install the Fixture Chain
and Ceiling Canopy
A. Adjust the Fixture Chain (B) to
your desired length by removing
links if needed. Put a cloth over
the Fixture Chain (B) to protect
the finish.
B. Pull the supply wires through
the Fixture Chain (B) alternating
links. After the wires are through
the Fixture Chain (B), pull the
Supply Wires and the Ground
Wire through the canopy lock
ring and the Ceiling Canopy (D)
in order.
C. Attach one end of the Fixture
Chain (B) to the fixture loop with
one Quick Link (C). Lift the
fixture and Fixture Chain (B) up
and attach the other end of the
Fixture Chain (B) onto the
canopy chain loop with another
Quick Link (C). The fixture will
now hang safely.
D. Feed the Supply Wires and
Ground Wire through the
canopy chain loop and nipple
into the outlet box. Cut the wires
leaving Approximately 8” of wire
extending from the Outlet Box.
E. Go to Step 3 for wire
connections and follow the
directions. Return to Step F in
this step when complete with