Installation Guide

Package Contents
1of1
Assembly Instruction Sheet
For Styles COR1611CU and COR1611K
A
Crossbar
Assembly
x1
F
Shade
x1
D
Socket
Assembly
x1
Figure 3
E
Socket Collar
x1
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar
Assembly (A). Attach the Crossbar
Assembly (A) to the outlet box with the
head of the green ground screw facing you.
Secure it with Outlet Box Screws (B).
Tighten until snug.
Supply Wires
with Ground Wire
Outlet
Box
Figure 1
STEP 2 Test Fitting Ceiling
Canopy to Crossbar Assembly
-
A.
eiling canopy on Socket
Assembly (D) to the
eiling canopy
Remove mounting balls from the
Crossbar Assembly (A). Fit the
c
Crossbar
Assembly (A) and secure with
mounting balls. Note: The
c
should be snug
on Socket
Assembly (D)
Mounting Screw
Hex Nut and
Lock Washer
D
Mounting Ball
Figure 2
A
against the and the mounting balls. Ifceiling not, adjust the length of
the nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the ceiling canopy on Socket Assembly (D) is
secure, remove the mounting ball and ceiling canopy and proceed to
Step 3.
A
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
(Step 3 Continued)
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard Wire Connectors (C) to make all wire connections.
Twist connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Figure 4
STEP 4 Install Socket Assembly-
A. Carefully tuck all wires into the
outlet box and position the ceiling
canopy of Socket Assembly (D)
over the outlet box. Align the holes
in the ceiling canopy with the
mounting screws. Attach Socket
Assembly (D) using the mounting
balls. Hand tighten until snug.
Mounting Screw
D
Mounting Ball
A
Figure 5
Bulb (not
included)
D
E
F
Top View
Key Hole
Mounting
Ball
STEP 5 Install Shade and Bulb-
A. Place Key Holes side of Shade
(F) over the socket. Pass Key
Holes on the Shade (F) over
Mounting Balls and rotate the
Shade (F) until it is secured in
place.
B. Thread the Socket Collar (E) to
socket and hand tighten until
snug.
C. Insert bulb onto socket and
screw snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19Medium Base Bulb 100W Maximum, bulb not included.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Outlet Box Screw
x2
B
Wire Connector
x3
C
B
2019 QuoizelInc.
ReleasedDate:2019-08-28
visit us on-line at www.quoizel.com
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture