Installation Sheet

ManualsBrandsQuoizel ManualsIndoor Ceiling FixturesBrockton 4 Light 18" Wide Semi-Flush Ceiling Fixture

Pleasegoto forproductcleaningtips.Gotothe selection.

(4)A19MediumBaseBulbs100WMaximumor

(4)MediumBaseVintageBulbsarerecommendedbutnotsupplied.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Note:This CONVERTIBLEfixturecanbemountedaschandelierlightorsemi-flushlight.Refertorespective

installationsteps forinstallations.

Warnings and Cautions

1of4

Assembly Instruction Sheet #IS-BRT1717GK

For Style BRT1717GK

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

2017 QuoizelInc.

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Hardware Contents

Crossbar

Lock Washer

1/4”H

Hex Nut

Nipple

Lock Ball

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184

or visit us on-line at www.quoizel.com

Fixture Body

ReleasedDate:2017-02-07

Knurled Nut

Canopy

Chain Loop

Canopy Lock

Ring

Ceiling

Canopy

Fixture Chain

Quick Link

Fixture

Loop

Nipple

Plate

Assembly Instructions for Chandelier Light

(Step 1A - Step 6A)

1/8”H

Hex Nut

STEP 1A Install Plate and Fixture Loop-

A. Thread one Knurled Nut (EE) to one end of the Nipple (B) until it is at

least 0.25” from the end. Thread the Lock Ball (FF) onto the end of

the Nipple (B) and hand tighten until snug.

B. Pass the Nipple (B) through the center hole of the ceiling canopy

from the bottom of the ceiling canopy. Thread one 1/8”H Hex Nut (C)

onto the top end of the Nipple (B) to secure the Nipple (B) to the

ceiling canopy.

C. Thread another 1/8”H Hex Nut (C) onto the Nipple (B), which is used

to support the Plate (D). Pass the Plate (D) over the Nipple (B).

Adjust the 1/8”H Hex Nut (C) to make sure the top surface of the

Plate (D) is flush to the top edge of the ceiling canopy.

(Step 1A Continued)

D. Pass the supply wires

and ground wire through

the wire exiting hole on

the Plate (D). Thread

another Knurled Nut (EE)

onto the top end of the

Nipple (B) to secure the

Plate (D). Hand tighten

until snug.

E. Thread the Fixture Loop

(A) onto the top end of

the Nipple (B) and hand

tighten until snug.

Figure 1A

Ceiling

Canopy

Supply Wires

and Ground Wire

STEP 2A Install the Crossbar to the junction box-

A. Attach the Crossbar (AA) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included), tighten until snug

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

Figure 2A

STEP 3A Install the Canopy Chain Loop and Nipple-

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end

of the Nipple (DD) and thread the Canopy Chain Loop (GG) onto

the Nipple (DD). By using pliers, thread the Hex Nut (CC) against

the Canopy Chain Loop (GG) and hand tighten until snug.

B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).

Place another Lock Washer (BB) over the Nipple (DD) and then

thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD)

is about 0.375” above the Crossbar (AA).

Summary of content (4 pages)

PAGE 1
Assembly Instruction Sheet #IS-BRT1717GK For Style BRT1717GK 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (4) A19 Medium Base Bulbs 100W Maximum or (4) Medium Base Vintage Bulbs are recommended but not supplied.
PAGE 2
(Step 3A Continued) (Step 5A Continued) C. Remove the Canopy Lock Ring (HH) from the Canopy Chain Loop (GG). Place the Ceiling Canopy (KK) over the Canopy Chain Loop (GG) against the ceiling to determine the correct position of the Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain Loop (GG). Adjust the Nipple (DD) to allow the Ceiling Canopy (KK) to rest against the ceiling when held in place by the Canopy Lock Ring (HH). D. Remove the Canopy Lock Ring (HH) and the Ceiling Canopy (KK).
PAGE 3
STEP 1B - Install the Crossbar to the junction box STEP 4B - Install Fixture Body to Ceiling A. Attach the Crossbar (AA) to the Outlet Box with the head of the Green Ground Screw facing you. Secure it with Outlet Box Screws (not included), tighten until snug . A. Attach the ceiling canopy and Fixture Body (E) over the end of the Nipple (DD) and secure with Knurled Nut (EE). Hand tighten until snug. B. Thread the Lock Nut (FF) onto the end of the Nipple (DD) and hand tighten until snug.
PAGE 4
BRT1717GK NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" FINISH: GREY ASH CHANDELIER 5” Dia. 67” OVERALL HEIGHT ( INCLUDES 48” CHAIN AND 2 QUICK LINKS ) 14.25” 17.5” Dia. SEMI-FLUSH 5” Dia. 12” 17.5” Dia. 2017 QuoizelInc. Thank you for purchasing a Quoizel product. Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.